JRC JFE-700 Instruction Manual Download Page 70

Page: 70 / 100

4. Operation

4-36

●

Visual display of alerts

Unacknowledged alarm and warning flash on Alert Messages and Alert Details Area. Caution is only lighting.

After acknowledged, alarm and warning are lighting.

Alert List function

The Alert List function can also be selected from the main menu.

Touch

and

, the Alert List screen will be displayed.

Alert History

JFE-400/700 Echo Sounder can display a list of alerts that have occurred in the past.

Touch

and

, the Alert List screen will be displayed.

・

Touch

to move to previous / next page.

・

When

is touched, return to previous menu.

・

Touch

to move to previous / next page .

・

When

is touched, return to previous menu.

・

When

is touched, print Alert History.

・

When

is touched, stop printout.

* The Alert History can display up to 40 past alerts.

* The displayed content is the same as the content of the Alert Detail area.

Summary of Contents for JFE-700





































































































Search results

Summary of Contents for JFE-700

Reviews:

Brands by name

Popular brands

JRC JFE-700, Instruction Manual

Search results

Summary of Contents for JFE-700

Reviews:

Brands by name

Popular brands