background image

 

4. Operation 

4-9 

   

Setting Cursor Display

 

   

                                         

 

The cursor display method in a standard mode and a history mode is selected. 

 

 

 

・ 

Depth cursor can move to the depth of touch position when depth cursor is displayed. 

・ 

After cursor moving ,use 

 and 

  for adjusting depth cursor. 

 

   

Display setting of sea bottom line

                                         

 

 

Select whether to simplify the sea bottom echo notation. 

 

 

 

 

 

 

 

 

 

・ 

Touch 

  and the settings will be displayed. 

Set content 

 

OFF/ON

 

   

 

OFF

 

 

Normal echo display. 

   

 ON  

  Shows a red line on the edge of the sea bottom echo. 

・ 

Change the settings with 

・ 

After setting, touch 

 

・ 

Touch 

  and the settings will be displayed. 

Set content

 OFF/ON/

AUTO

 

OFF

The Depth cursor is not always displayed 

ON

  The Depth cursor is always displayed. 

AUTO

  The Depth cursor disappears from the screen when the   

non-operation time reaches 30 seconds. When the depth   

cursor disappears, tap the screen to redisplay it. 

・ 

Change the settings with 

・ 

After setting, touch 

Summary of Contents for JFE-700





































































































Reviews: