JRC JFE-700 Instruction Manual Download

Page: 33 / 100

3. Display

3-3

3.3 Docking mode

The docking mode displays depth data bigger.

[Sample screen at single frequency]

[Sample screen at dual frequency]

No. Function

Description

Display mode

The current display mode is displayed.

Date and time

Date and time information from GPS are displayed. When not connected, the internal
clock will be displayed.

Latitude / Longitude

Latitude / Longitude from GPS is displayed.

4 Frequency

and

equipment position

The frequency and equipment position of the transducer are displayed.

Draft value

The entered draft value is displayed.

Keel value

The entered keel value is displayed.

Gain value

The current gain value is displayed. “Auto” is displayed when auto gain is selected.

Depth value

The current water depth value is displayed digitally.

Depth display setting

The currently selected depth display setting is displayed.

Range

The range with the displayed water depth value in use is displayed.
"Auto" is displayed when auto range is selected.

Note:

・

LAT/LON display needs to connect position data device.

Summary of Contents for JFE-700





































































































Search results

Summary of Contents for JFE-700

Reviews:

Related manuals for JFE-700

Brands by name

Popular brands

JRC JFE-700, Instruction Manual

Search results

Summary of Contents for JFE-700

Reviews:

Related manuals for JFE-700

Brands by name

Popular brands