manualshive.com logo in svg

JRC JFE-700, Instruction Manual

Share
Download
JRC JFE-700 Instruction Manual Download Page 37

4. Operation 

4-3

 

    Selecting Display Mode [MODE]                                                                                   

・ 

Each time with 

  touch, the display mode changes. 

Single frequency

: Each time with 

  touch, the display mode changes as follows.

 

Standard mode:   

CH1 

   

 

↓

 

History mode: 

HIST_CH1 

   

 

↓

 

Docking mode: 

DOCKING 

   

 

↓

 

Return to the Standard mode 

Dual frequency

:

 

Each time with 

  touch, the display mode changes as follows.

 

Standard mode: 

CH1

  →

 CH2

  →

 CH1/CH2 

↓

 

History mode   

HIST_CH1

  →

 HIST_CH2

  →

 HIST_CH1/CH2 

↓

 

Docking mode 

DOCKING 

 

 

↓

 

Return to the Standard mode 

 

    Draft control [DRAFT]                                                                                               

・ 

Draft can be set to 0

～

50m in 0.1 step. 

・ 

Touch 

  on main screen. The button color change to green and draft menu is displayed. 

・ 

Draft value is displayed with highlight on main screen.   

・ 

Whenever 

  is touched, the draft value is raised. 

・ 

Whenever 

  is touched, the draft value is lowered. 

・ 

After setting the draft. touch green DRAFT button and gain menu is closed. 

・ 

When 2 transducers are installed, touch the green DRAFT button again to switch to the CH2 setting. 

 

 

 

 

 

 

 

Summary of Contents for JFE-700





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands