21
The following activation and setup procedure should be used for all JR XP8103 and XP8103DT (digital trim) systems.
Note:
Some early XP8103 systems will require the activation of the CCPM software through the Horizon Service Center. It’s easy to
identify if your system has the CCPM function activated by identifying if the “SWASH TYP” function appears in the System mode as
shown in Section A below. Please refer to Section A to access the System mode.
Prior to activating the CCPM function, it is first suggested that the Data Reset function be performed to reset the desired model number to
be used back to the factory default settings. If you are using a new radio system, proceed to Step B.
Caution:
Prior to performing the Data Reset function, it will be necessary to select the desired model number to be used.
A) Press the
Up
and
Down
keys simultaneously while turning the
power switch on to enter the system mode. Next, press the
Up
or
Down
keys to move the cursor to the Model Select function. Press
the
Up
and
Down
keys simultaneously to enter the Model Select
Function. Select the desired model number to be used, then press
the
Clear
key to reset the current model to the factory default
settings. Press the
Up
and
Down
keys simultaneously to exit the
Model Select function.
B) Press the
Up
or
Down
keys to move the cursor to the Swash Type function, then press the
Up
and
Down
keys simultaneously to access the
Swashplate Type function.
Note:
If the Swashplate Type function is not present, it
can be activated by the Horizon Service Center. Please call
for details.
Press the
Up
or
Down
keys until “3 servo 120°” appears on the
screen. Press the
Up
and
Down
keys simultaneously two times
to exit the Swashplate Type function and the System mode.
C) Turn the power switch on, then press the
Up
and
Down
keys simultaneously to enter the function
mode. Press the
Up
key until “SWASH MIX” appears on the screen. Once this has been completed,
it will be necessary to change the values as shown using the (+) and (-) keys.
D) Press the
Up
key until “REV. SW.” (Servo Reversing) appears on the screen. Next, reverse
Channels 2 and 4 by moving the cursor with the
CH
key, then pressing the (+) and (-) keys.
E) Press the
Up
key until “TRVL. ADJ.” (Travel Adjust) appears on the screen. Adjust the values as
shown using the channel key to move the cursor, and the (+) and (-) keys to set the value. Press
the
Sel
key to access the pitch channel values and set as indicated. Please note that the required
travel values will vary based on the type of servo selected. Please also note that the throttle travel
values may vary based on the type of engine used. This value can be fine tuned once the throttle
linkage has been installed.
Proceed to page 24.
CCPM SOFTWARE ACTIVATION AND INITIAL ADJUSTMENT (CONTINUED)
2. JR XP8103/XP8103DT SYSTEMS
[SYSTEM M.]
• INFO-DISP
• Model SEL
• MDL Name
• Type SEL
• MDL Reset
• MODULAT
• TRANSFER
• INPUT SEL
• SWASH TYP
[MDL Reset]
MODEL 1
HELI SPCM
PIT.
£H 100%
L 100%
AUX3
+ 100%
- 100%
[TRVL ADJ.]
£THRO
H 120%
L 120%
AILE
£L 100%
R 100%
ELEV
D 100%
U 100%
RUDD
£
L 150%
R 150%
[SWASH TYP]
1servo
NORM
[SWASH MIX]
3servos
120
•
[SWASH TYP]
3servos
120
•
3servos 120°
AILE
+70%
ELEV
+70%
∞ PIT.
-65%
Adjust Pitch Value to -65%
Throttle travel values may vary,
depending upon engine used.
[REV.SW]
1
2
3
4
5
6
7
8
ch
REV.
NORM.
Note:
The travel values shown for the
rudder function are for use with Piezo type
gyros, like the JR G410T and G460T.
