background image

Semi scale  model

40 Class

52 Class

2-cycle engine

4-cycle engine

RADIO CONTROLED ALMOST READY-TO-FLY ENGINE POWERED ALL BALSA PLANE

VQA09 / VQA091

Or Electric equivalent

BUILDING INSTRUCTIONS / MONTAGEANLEITUNG

SPECIFICATIONS

Wingspan
Length
Flying weight
Electric Motor
Glow Engine
Radio

Technische Daten

Spannweite
Länge
Fluggewicht
Elektroantrieb
Verbrennerantrieb
Fernsteuerung

1580mm

1160mm

2500g

650 Watt 

6,5cc 2T / 8,5cc 4-T

7 Channel / 7 Servos

1580mm

1160mm

2500g

650 Watt 

6,5cc 2T / 8,5cc 4T

7 Kanal / 7 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Summary of Contents for P-39 Q/N AIRACOBRA













Reviews: