Jøtul Scan 45i TSI Installation And Operation Instructions Manual Download Page 5

5

139472_Rev_B   8.28.12

General Information

IMPORTANT:  SAVE THESE INSTRUCTIONS.

1.  The installation and repair of this appliance must be 

done by a qualified service person. Failure to properly 

install and maintain this heater could result in an 

unsafe or hazardous installation, which may result in 

a fire, explosion, property damage, personal injury or 

loss of life. 

2.  This appliance should be inspected before use and 

at least annually. More frequent cleaning may 

be required due to excessive lint from carpeting, 

bedding material, pet hair, etc. It is imperative that 

control compartments, burners and circulating air 

passageways of the appliance be kept clean.

  `S’assurer que le bruleur et le compartiment des com-

mandes sont propres. Voir les instructions d’installation 

et d’utilisation qui accompagnent l’appareil.

3.  This appliance may be installed in an aftermarket 

permanently located, manufactured (mobile) home, 

where not prohibited by local codes.  

This appliance is only for use with the type(s) of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases, unless a certified 

kit is used. 

  Cetappareil peut être installé dans un maison préfab-

riquée (mobile) déjà installée à demeure si les règle

-

ments locaux le permettent.

  Cet appareil doit être utilisé uniquement avec les 

types de gas indiqués sur la plaque signalétique. Ne 

pas l’utiliser avec d’autres gas sauf si un kitde conver-

sion certifié est installé.

4.  The installation must conform to local codes. Your lo-

cal Scan authorized dealer can assist you in determin

-

ing what is required in your area for a safe and legal 

installation. Some areas require a permit to install 

a gas burning appliance. Always consult your local 

building inspector or authority having jurisdiction to 

determine what regulations apply in your area. 

  In the absence of local codes, the installation require-

ments must comply with the current National codes. 

In the U.S., these requirements are established in the 

National Fuel Code, ANSI Z223.1.(NFPA 54). In Canada, 

the codes have been established in CAN/CGA B149 

Fuel Installation Code. 

  Installer l’appareil selon les codes ou reglements 

locaux, ou, en l’absence de tels reglements, selon les 

Codes d’installation CAN/CGA-B149.

5.  Do not operate this fireplace if any part of it has 

been under water.

  Immediately call a qualified service technician to 

inspect the heater and to replace any part of the 

control system and any gas control which has been 

under water.

  Ne pas se servir de cet appareil s’il a ete’ plonge dans 

l’eau, completement ou en partie.  Appeler un tech-

nicien qualifie pour inspecter l’appareil et remplacer 

toute partie du syste’me de controle et toute com-

mande qui ont ete plonges dans l’eau.

6.  Do not operate the fireplace with the glass front re

-

moved, cracked or broken. Replacement of the glass 

should be done by a licensed or qualified service 

person.  Only remove glass for routine service. Always 

handle glass carefully.

  Pour utilisation avec les portes en verre cerifiers aved 

l’appareil seulemend ou. Ne pas utiliser avec des 

portes on verre. 

7.  Notify your insurance company before proceeding 

with installation of this fireplace.

THIS HEATER MUST BE INSTALLED AND MAIN

-

TAINED BY A QUALIFIED SERVICE AGENCY.  

DO NOT ATTEMPT TO ALTER OR MODIFY THE 

CONSTRUCTION OF THIS APPLIANCE OR ITS COM-

PONENTS. ANY MODIFICATION OR ALTERATION 

WILL VOID THE WARRANTY, CERTIFICATION AND 

LISTING OF THIS APPLIANCE.

Your fireplace insert has a unique serial number 

stamped on the rating plate which is located in the valve 

compartment. Please record the serial number in the 

space below. You may also wish to attach your purchase 

receipt to this page for future reference.

MODEL NAME:   Scan 45i TSI Direct Vent Gas Fireplace 

Insert

SERIAL NUMBER:_______________________________

 

DATE OF PURCHASE:____________________________

AUTHORIZED DEALER:__________________________

 

 

   ADDRESS ___________________________________

 

 

   PHONE: ____________________________________

   INSTALLER:__________________________________

 

FUEL TYPE:____________________________________

FUEL CONVERSION:                  NO _______       YES_____

NOTES:________________________________________

______________________________________________

______________________________________________

Summary of Contents for Scan 45i TSI

































Reviews: