Jøtul GI 350 DV, Installation And Operation Instructions Manual

Page: 16 / 32

16
Conversion Kit Contents:
#156444 - LP #156445 - NG
• 1 Regulator Tower labeled for Propane
• 3 Regulator Tower Screws
• 1 Burner Orifice (#38” NG, 1.50 mm LP)
• 1 Pilot Orifice (#30 for LP, #51 for NG)
• Label A - to be completed and applied to the
control valve.
• Label B - apply to the fireplace Rating Plate as
designated on the plate.
Tools required:
• 1/2” or 13 mm deep well socket and wrench
• Torx T-20 or small spade screwdriver
• 4 mm hex key, included in kit
C C
C C
CA A
A A
AU U
U U
UT TT
T
TION: ION:
ION: ION:
ION: Before proceeding with the gas conver-
sion, the gas supply must be shut off prior to
disconnecting electrical power.
Fuel Conversion Procedure
1. 1. 1. 1. 1. R R R R Remo emo emo emo emov vv vve e e e e the Burner assembly the Burner assembly the Burner assembly the Burner assembly the Burner assembly:::::
••••• If you have not already done so, remove the fettle
and log set from the firebox. CAUTION: THE LOGS
ARE FRAGILE. Handle them with care and set aside
out of the way. See fig. 13.
• Remove the Log Support attached to the rear of the
firebox.
• Loosen the wingnut on the Air Shutter Stem,
located under the center of the firebox floor, and
push the stem as far as it will go toward the back of
the insert. Disengage the burner assembly with the
Air Shutter by lifting it up and back, out of the
firebox. Swing the Air Shutter out of the way to
access the burner orifice. Fig. 14.
2. 2. 2. 2. 2. Chang Chang Chang Chang Change e e e e the Burner Orific the Burner Orific the Burner Orific the Burner Orific the Burner Orifice: e: e: e: e:
• Using a 13 mm deep well socket, remove the
burner orifice and replace with the appropriate
orifice, supplied in the kit. Tighten securely.
3. 3. 3. 3. 3. Chang Chang Chang Chang Change e e e e the Air Shutter position: the Air Shutter position: the Air Shutter position: the Air Shutter position: the Air Shutter position: Lift the shutter
tube up in its hinge pin slots and turn the tube
over, so that the appropriate fuel type indicator
(LP or NG) is oriented facing you. See fig. 15.
4 4
4 4 4..... Chang
Chang
Chang Chang Change
e
e e e the P
the P
the P the P the Pilot
ilot
ilot ilot ilot Orific
Orific
Orific Orific Orifice:
e:
e: e: e:
• • • • • Disengage the Pilot Hood by releasing the
retainerclip as shown in Fig. 16. Using a 4 mm
allen wrench, unscrew the pilot orifice (counter-
clockwise). Replace with the orifice from the kit.
Tighten new orifice securely into the base of the
pilot assembly.
Fuel Conversion
The Jøtul GI 350 Fireplace is designed to for use with
either Natural gas or Propane. It is shipped from the
factory configured to use Natural gas. A conversion
kit is included for conversion to Propane use if
desired. Check the identification label on the Control
Valve to confirm that the correct fuel is used.
WARNING:
THE CONVERSION KIT IS TO BE INSTALLED BY AN
AUTHORIZED JØTUL SERVICE TECHNICIAN IN ACCOR-
DANCE WITH THE MANUFACTURER’S INSTRUCTION
AND ALL CODES AND REQUIREMENTS OF THE AUTHOR-
ITY HAVING JURISDICTION. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE. THE QUALIFIED AGENCY PER-
FORMING THIS WORK ASSUMES RESPONSIBILITY FOR
THIS CONVERSION.
IN CANADA:
THE CONVERSION SHALL BE CARRIED OUT IN ACCOR-
DANCE WITH THE REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING JURISDICTION AND IN ACCOR-
DANCE WITH THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
Cet equipement de conversion sera installe par une
agence qualifiee de service conformement aux
instructions du fabricant et toutes exigences et codes
applicables de l’autorises avoir la juridiction. Si
l’information dans cette Instruction n’est pas suivie
exactement, un fey, explosion ou production de
protoxyde de carbone peut resulter blessure
personnelle de vie. L’agence qualifiee de service est
esponsable de l’installation n’est pas propre et
complete jusqu’a l’operation de l’appareil converti est
cheque suivant les criteres etablis dans les instruc-
tions de proprietaire provisionnees avec
l’equipement.
Figure 13. Firebox component identification.
Burner
Fettle
Air Shutter Stem under firebox floor
Log Support
Pilot Assembly