Johnson Controls Sabroe SAB 193 L, Manual

Page: 171 / 171

End plate, coalescer
Mounting method Torque
[Nm]
1 bolt 28
3 bolts 12
If not otherwise indicated, use the torque table above.
Suction flange
Compressor model Bolt
size
Torque
[Nm]
SAB 120 S-E M22 390
SAB 151 S-E M24 550
SAB 193 S M20 375
SAB 193 L M20 375
SAB 233 S M20 375
SAB 233 L M20 400
SAB 233 E M22 400
SAB 283 S-L M22 400
SAB 283 E M24 400
SAB 355 S-L-E-X M30 550
SAB 157 HR M22 300
Danfoss POV
Size
Torque
[Nm]
POV 600 / DN 40 44
POV 1050 / DN 65 75
POV 2150 / DN 80 44
Danfoss ORV 3-way, cover
Size
Torque
[Nm]
H1 DN25-DN40 30
H2 DN50-DN60 50
H3 DN65-DN80 80
Danfoss SVA cover/
KDC 65-200 (2½-8 in.)
Size
Torque
[Nm]
DN 15-20 22
DN 25-32-40-50 44
DN 65 75
DN 80 44
DN 100 75
DN 125-150 183
DN 200 370
Compressor
model
Compressor flange
for oil separator
Bolt size Torque
[Nm]
SAB 120 S-E M20 203
SAB 151 S-E M22 226
SAB 193 S M20 190
SAB 193 L M20 190
SAB 233 S M20 217
SAB 233 L M20 217
SAB 233 E M20 217
SAB 283 S-L M22 311
SAB 283 E M22 311
SAB 355 S-L-E-X M24 510
SAB 157 HR M20 190
End cover, oil separator
Compressor model
Torque
[Nm]
All See torque table
Mount the cutting ring and union
nut correctly in the fitting.
Press the pipe all the way to the
bottom.
Turn the union nut until it
reaches its fixture point (when
the pipe cannot turn).
Tighten the union nut 180
degrees using a key.
Mounting is completed.
Use 7 bar leak test on all:
•
pipe joints
•
fittings
•
flanged joints
•
welds
See instruction 0186.12:
‘7 bar leak detection’.
Valve block
Ø 5 6 Nm
Ø6 14 Nm
Note!
Mark all bolts with a yellow marker
when they are torqued.
Gaskets and O-rings
•
Joints with gaskets must always be cross-tightened.
•
Moisten the joining surfaces on gaskets and O-rings with oil, and wipe them lightly so
that the surfaces are slightly greased.
•
Oil for greasing of joining surfaces:
o
Mobil Rarus 424 (part no. 6993.007)
o
Vanguard 1000 (part no. 2031.075)
•
Do not grease gaskets and O-rings with oil as it may damage the gasket/O-ring.
Grease the screws and bolts.
Rust-proof with:
MOLYKOTE(R) LONGTERM W2
8 Nm (M8 12.9) (Filter cartridge)
Note! Cross-tighten the bolts
Torpedo filter:
1. Tighten by hand
2. 88 Nm
3. 176 Nm
Note! Cross-tighten in the last two steps
Westermeyer filter:
1. Tighten by hand
2. 23 Nm
3. 48 Nm
Counter-tighten, see torque table
Sight glass:
15 Nm