Johnson Controls Intelligent Fire Integrator NION-16C48M Installation & Operation Manual Download Page 7 | Manualshive

Page: 7 / 40

background image

7

NION-16C48M Installation & Operation Manual - P/N: 53347:Rev: A1 5/5/09

Section 1 About this NION

1.1 Agency Listings

1.1.1 Compliance

This product has been investigated to, and found to be in compliance with the following standards.

National Fire Protection Association

•

NFPA 72

—National Fire Alarm Code

Underwriters Laboratories

•

UL-864

—Control Units for Fire Alarm Systems, Ninth Edition

•

UL-1076

—Proprietary Burglar Alarm Units and Systems, Fifth Edition

Underwriters Laboratories Canada

•

CAN/ULC-S527-99

—Standard for Control Units for Fire Alarm Systems, Second Edition

•

CAN/ULC-S559-04

—Equipment for Fire Signal Receiving Centres and Systems, First

Edition

1.1.2 Installation

This product is intended to be installed in accordance with the following regulatory agencies.

Local

•

AHJ

—Authority Having Jurisdiction

National Fire Protection Association

•

NFPA 70

—National Electrical Code

•

NFPA 72

—National Fire Alarm Code

•

NFPA 101

—Life Safety Code

Underwriters Laboratories

•

UL-1076

—In certified applications, the unit shall be installed in accordance with Proprietary

Burglar Alarm Units and Systems, Fifth Edition

Underwriters Laboratories Canada

•

CAN/ULC-S524-06

—Standard for the Installation of Fire Alarm Systems, Fifth Edition

•

CAN/ULC-S561-03

—Installation and Services for Fire Signal Receiving Centres and

Systems, First Edition

NOTE:
UL 864, 9th Edition

—Intelligent Fire Integrator™

systems work with products that have been UL

864, 9th Edition listed as well as products that have not received UL 864, 9th Edition certification.
Operation of systems that are comprised of equipment that is UL 864, 9th Edition listed together
with products that are not UL 864, 9th Edition listed requires the approval of the local Authority
Having Jurisdiction (AHJ).

CAN/ULC-S559-04, 1st Edition

—Intelligent Fire Integrator™

systems work with products that

have been CAN/ULC-S559-04, 1st Edition listed as well as products that have not received
CAN/ULC-S559-04, 1st Edition certification. Operation of systems that are comprised of
equipment that is CAN/ULC-S559-04, 1st Edition listed together with products that are not
CAN/ULC-S559-04, 1st Edition listed requires the approval of the local Authority Having
Jurisdiction (AHJ).

«
...
5
6
7
8
9
...
»

Summary of Contents for Intelligent Fire Integrator NION-16C48M









































Reviews:

No comments

Related manuals for Intelligent Fire Integrator NION-16C48M

Brand: Mackie Pages: 14

Brand: Oklahoma Sound Pages: 4

Brand: Aaron Pages: 2

Brand: Aaron Pages: 3

Brand: Farfisa Pages: 72

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 2

Brand: ZKTeco Pages: 16

ACUSTICA H series

Brand: RCF Pages: 10

Brand: Cerdi Pages: 24

Brand: JBL Pages: 6

IQeye Sentinel Series

Brand: Iqinvision Pages: 15

treeMOTION S.light USCA

Brand: TEUFELBERGER Pages: 152

Brand: Fike Pages: 4

Brand: Doberman Pages: 6

Brand: Q-See Pages: 1

WISENET XNO-8080R

Brand: Hanwha Techwin Pages: 13

Brand: DBI SALA Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands