Johnson Controls Intelligent Fire Integrator NION-16C48M Installation & Operation Manual Download Page 22 | Manualshive

Page: 22 / 40

background image

Description and Installation

NION Power and Serial Data Connections

22

NION-16C48M Installation & Operation Manual - P/N: 53347:Rev: A1 5/5/09

NION-16C48M Terminal Boards

The NION-16C48M incorporates two terminal daughter boards (16C48MTB) that are mounted
directly to the motherboard using included stand-offs.  Both terminal boards are identical and
interchangeable.  Each terminal board is connected to the motherboard via included ribbon cables
(four per terminal board).  Point designation for each terminal is determined by the position of the
terminal board on the motherboard.  Refer to the diagrams below for terminal board mounting and
ribbon cable connections.

Figure 2.10 16C48MTB Terminal Board Mounting

U44

U6

- +

Mounting standoffs

This standoff is also used to attach

the motherboard to the cabinet.

Terminal board 2

Terminal board 1

Cable sockets

P1-P4

Cable sockets

P1-P8

Mounting standoff

«
...
20
21
22
23
24
...
»

Summary of Contents for Intelligent Fire Integrator NION-16C48M









































Reviews:

No comments

Related manuals for Intelligent Fire Integrator NION-16C48M

Brand: Olympia Pages: 5

Brand: Lampa Pages: 2

Brand: Xilica Audio Design Pages: 10

Brand: jacarta Pages: 4

SET-2000 Oil/Sludge

Brand: Labkotec Pages: 14

Brand: Radiodetection Pages: 2

Scopia XT Advanced

Brand: Avaya Pages: 2

Brand: Novus Pages: 36

Brand: Brickcom Pages: 7

Brand: LSS Pages: 14

Versa'larm VA01A

Brand: Alderon Industries Pages: 4

Brand: Longevity Pages: 25

AmpliFi Protect

Brand: Ubiquiti Pages: 36

Brand: Velleman Pages: 31

Brand: ubbink Pages: 61

Brand: Dahua Technology Pages: 18

Brand: M-system Pages: 2

SKY PRO 10 CPC 58

Brand: KU Solar Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands