background image

 

                            

 

FRICK

 QUANTUM™LX AcuAir



 CONTROL PANEL                    090.510-M (OCT 10) 

                                                            MAINTENANCE                                                                           Page 7

remove the DVM probes from the Quantum™, and 
install them into the white connector on the last I/O 
board in the daisy-chain, as shown below:    

 
 
 
 
 
 
 
 
 
 

Check the reading on the DVM. If the reading at the 
Quantum™ has been adjusted properly, then this 
reading can be no lower than +5.0 DC. If the voltage 
is less, check all of the daisy-chain connections on 
the blue DC-I/O harness. Ensure that all of its 
connectors are tight. If all connections are good, then 
go back and start measuring over again, this time 
beginning at the first board in the daisy-chain. 
Continue checking the voltage at each connection, 
until you locate the point at which the voltage drop is 
excessive. This will usually indicate a connection that 
is not being made properly, or the sockets within the 
connector are weak. In either case, the DC-I/O wire 
harness may need replacing. 
 
Next, you will want to measure the +12 Vdc. Perform 
the same steps as with the +5 Vdc measurement, with 

the exception that you will not need to measure at the 
Quantum™. Measure directly at the last connection. If 
the voltage is low, ensure that there is not an 
excessive voltage drop in the daisy-chain. If the 
voltage is out of range, then the supply itself may 
need replaced.  
 
The -12 Vdc may be measured the same as the other 
voltages, however, this voltage is not adjustable on 
any supply, so if the harness is not the culprit, the 
supply may need to be replaced.  

 

REPLACEMENT 

 

If the power supply is found to be bad, or not capable 
of acceptable adjustment, it will need replacing. When 
ordering this replacement, you will receive an upgrade 
kit. The purpose of this kit is to allow for the upgrading 
of the I/O DC power harness, at the same time as 
replacing the power supply. Refer to the 
Recommended Spare Parts list for the upgrade part 
number. This upgrade kit will include the following 
components: 

 

 

Screws (6-32 x 3/8 flat head) 

 

Power supply (Condor) 

 

DC power cable harness (this is an improved 
version of the previous power cable) 

 

+5 DC Voltage Measurement Location 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
 
 

+5V 

RET 

PL13

LK9

LK8 LK10 

PL16 

PL8 

PWR 

SUSP

FLASH

LK11 LK12 

PL24 

PL3

PL

LK1 

PL7

PL9

LK2 

PL17

PL12

PL19 

PL18 

PL14 

PL10 

PL6 

PL2

PL4

PL1

 

Flash Card 

Socket 

(Located 

under 

board) 

PL3 

PL5 

PL11 

LK3 


LK4 

PL15 

TB1

TB2

LK2

COM-2 

TB3

RS-232

3

1

LK6

B A

LK5

LK7

COM-2

COM-1

1

2

3

4

1

2

3

4

LK8

LK7

LK10

LK9

D3

LK16

A
B

A
B

PL2

3

 

O

D8

D10

D11

D12

PORT 80H

D4

D5

D7

D13

SW1

ON

1

2

3

4

5

6

7

8

D6

D2

LK11

B
A

LK1

LK4

LK3

LK6

LK5

D1

D8

LK17

RS-422 
RS-485

RS-422 
RS-485

PL1 

+5 VDC 

(Red Lead)

Common 

(Black Lead)

A voltage 

regulator to 

the flash port 

allows the 

Quantum™ 4 

5 VDC to be 

set to 

+5.15VDC to 

5.20 VDC as 

measured 

here.

 

Summary of Contents for FRICK QUANTUM LX AcuAir





































Reviews: