Joannes ALPA 31 BS 60, Instructions For Use, Installation And Maintenance

Page: 23 / 68

ALPA 31 BS 60
23
EN
cod. 3541B530 - 01/2012 (Rev. 00)
Adjustment of pressure at burner
Since this unit has flame modulation, there are two fixed pressure values: the minimum
and maximum, which must be those given in the technical data table according to the
type of gas.
• Connect a suitable pressure gauge to pressure point "B" downstream of the gas
valve
• Disconnect the pressure compensation tube “H” and remove the protection cap
“D” , undoing screw “A” .
• Operate the boiler in TEST mode.
• Set the heating power to 100.
• Adjust the max. pressure with screw "G" , clockwise to increase it and anticlockwise
to decrease it
• Disconnect one of the two fastons from modureg "C" on the gas valve.
• Adjust the min. pressure with screw "E" , clockwise to decrease it and anticlockwise
to increase it.
• Reconnect the faston detached from the modureg on the gas valve.
• Check that the maximum pressure has not changed.
• Reconnect the pressure compensation tube “H” .
• Refit the protection cap “D” .
• To end the TEST mode, repeat the activation sequence or wait 15 minutes.
A
After checking or adjusting the pressure, make sure to seal the adjust-
ment screw with paint or a specific seal.
fig. 26 - Gas valve
A - Protection cap screw
B - Downstream pressure point
C - Modureg cable
D - Protection cap
E - Min. pressure adjustment
G - Max. pressure adjustment
H - Compensation tube
Heating power adjustment
To adjust the heating power, switch the boiler to TEST mode (see sec. 3.1). Press the
heating buttons fig. 1 (details 3 and 4 - ) to increase or decrease the power (min. = 00 -
max. = 100). Press the RESET button within 5 seconds and the max. power will remain
that just set. Exit TEST mode (see sec. 3.1).
Lighting power adjustment
To adjust the lighting power, switch the boiler to TEST mode (see sec. 3.1). Press the
DHW buttons (details 1 and 2 - fig. 1) to increase or decrease the power (min. = 00 - max.
= 60). Press the RESET button within 5 seconds and the lighting power will remain that
just set. Exit TEST mode (see sec. 3.1).
Service menu
The card is equipped with two Menus: one for configuration and the other for Service.
The configuration Menu is accessed by pressing the DHW buttons together for 10 sec-
onds. 2 parameters, modifiable only from card, are available.
If replacing the card, always set the parameter P01 to 0=Copper.
To exit the configuration Menu, press the DHW buttons together for 10 seconds.
The card Service Menu is accessed by pressing the Reset button for 10 seconds. Press
the Heating buttons to select "tS", "In", "Hi" or "rE". tS” means Transparent Parameters
Menu, “In” Information Menu, “Hi” History Menu, and “rE” History Menu Reset. After se-
lecting the Menu, press the Reset button to access it.
"tS” - Transparent Parameters Menu
The card is equipped with 24 transparent parameters also modifiable from Remote Con-
trol (Service Menu):
Press the Heating buttons to scroll the list of parameters in increasing or decreasing or-
der. Press the DHW buttons to modify the value of a parameter: the change will be au-
tomatically saved.
The Max. Heating Power and Lighting Power parameters can be modified in Test Mode
(see relevant section).
Press the Reset button to return to the Service Menu. Press the Reset button for 10 sec-
onds to exit to the card Service Menu.
"In" -Information menu
The card can display the following information:
Press the Heating buttons to scroll the list of information. In case of damaged sensor, the card
displays hyphens.
Press the Reset button to return to the Service Menu. Press the Reset button for 10 seconds to
exit the Service Menu.
"Hi" - History menu
The card can store the last 10 faults: the History datum item H1: represents the most recent fault
that occurred; the History datum item H10: represents the least recent fault that occurred.
The codes of the faults saved are also displayed in the corresponding menu of the Opentherm re-
mote control.
Press the Heating buttons to scroll the list of faults. Press the DHW buttons to display the value.
Press the Reset button to return to the Service Menu. Press the Reset button for 10 seconds to
exit the Service Menu.
"rE" - History reset
Press the M button for 3 seconds to delete all the faults and times stored in the History Menu: the
card will automatically exit the Service Menu, in order to confirm the operation.
Press the Reset button to return to the Service Menu.
Remote control Card Description of transparent parameters Range Default
NO P01 Exchanger type selection 0=Copper
1=Cast iron 0=Copper
NO P02 Boiler shell Warm-up activation temperature 0-80°C 0°C
H
C
D
B A
D
H
C
E
G
Remote
Control Card Description of transparent parameters Range Default
01 P01 Gas type selection 0=Natural gas
1=LPG 0=Natural gas
02 P02 Boiler type selection 1=Heating only
2=Storage with probe
3=Storage with ther-
most. 2=Storage with
probe
03 P03 Absolute min. power 0-100% 0%
04 P04 Lighting power 0-60% 50%
05 P05 Not used Not modifiable 0
06 P06 Heating train 1-20°C/min 5°C/min
07 P07 Heating pump Post-Circulation 0-20 minutes 6 minutes
08 P08 Heating standby time 0-10 minutes 2 minutes
09 P09 Max. heating power 0-100% 100%
10 P10 Pump operation 0=Post-Circulation
1=Continuous 0=Post-Circulation
11 P11 Pump deactivation temperature during Post-
Circulation 0-100°C 20°C
12 P12 Max heating temperature 31-85°C 85°C
13 P13 DHW pump Post-Circulation 0-255 seconds 30 seconds
14 P14 DHW standby time 0-255 seconds 120 seconds
15 P15 DHW max. power 0-100% 100%
16 P16 DHW user max. setpoint 55-65°C 65°C
17 P17 Hot water tank activation hysteresis tempera-
ture 0-20°C 2°C
18 P18 Hot water tank preparation delivery tempera-
ture 70-85°C 80°C
19 P19 Not used Not modifiable 0
20 P20 Not used Not modifiable 4 bar/10
21 P21 Not used Not modifiable 8 bar/10
22 P22 Legionella protection 0-7 0
23 P23 Not used Not modifiable 0
24 P24 Mains Voltage Frequency 0=50Hz
1=60Hz 0=50Hz
t01 Heating NTC sensor (°C) between 05 and 125 °C
t02 DHW NTC sensor (°C) between 05 and 125 °C
t03 Safety NTC sensor (°C) between 05 and 125 °C
t04 External NTC sensor (°C) between -30 and 70°C (Negative values flash)
L05 Actual burner power (%) 00%=Min., 100%=Max.
P06 Actual system water pressure (bar/10) 00=Pressure switch open
14= Pressure switch closed
F07 Actual ionisation current (uA) 00=burner off