manualshive.com logo in svg

JLG X13JP-X370AJ, Service And Maintenance Manual, Page: 112 / 137

Share
Download
JLG X13JP-X370AJ Service And Maintenance Manual Download Page 112

SECTION 6 - JLG CONTROL SYSTEM

6-10

3121774

MICROJIB AB

DOWN
DOWN

The JIB is closed - the control switch is released, line A is open and line B is closed 

UP
UP

The JIB is open - the control switch is pressed, line A is closed and line B is open

PEDAL AB

ON
ON

The pedal is pressed- the pedal electric line A is open and line B is closed 

OFF
OFF

The pedal is released - the pedal electric line A is closed and line B is open

R.C. BASKET

ON

The remote control is in the support in basket 

OFF

The remote control is not in the support in basket

TRACK OPEN A

ON

Left track is fully widened. Widening cylinder of left track contact is closed

OFF

Left track is not fully widened. Widening cylinder of left track contact is open

TRACK OPEN B

ON

Right track is fully widened. Widening cylinder of right track contact is closed

OFF

Right track is not fully widened. Widening cylinder of right track contact is open

INCLIN. X

0.05

Indicates the inclination of the machine on the X axis in degrees 

INCLIN. Y

0.3

Indicates the inclination of the machine on the Y axis of degrees

LOAD AB

134
133

Indicates the weight of the basket (about 50 Kg) plus the weight into the basket in Kg measured by A and B 
lines

POS. 3 ARM

2073

Indicates the opening of the 3rd boom cylinder in tenths of a millimeter

PROXIMITY

ON

Turret is not almost completely rotated, contact is close, 1st-2nd booms are not above the engine

OFF

Turret is almost completely rotated, contact is open, 1st-2nd booms are above the engine

MICR. BR. 1-2

ON

Indicates that 1st boom is not opened enough to rotate above the engine carter

OFF

Indicates that 1st boom is opened enough to rotate above the engine carter

SKYGUARD

ON

Indicates that Skyguard bar has been pressed.

OFF

Indicates that Skyguard bar has not been pressed.

MOTOR RPM
(Only for Diesel 
machine)

2220

 Indicates the Diesel engine rpm

TEMPERAT.

37,62

Indicates the temperature of the ECM1 in °C

SUPPLY (V)

12,15

Indicates the batteries voltage, or the output voltage from the battery charger 

Go 

to 

Discount-Equipment.com 

to 

order 

your 

parts

Summary of Contents for X13JP-X370AJ










































































































































Reviews:

No comments