background image

  FOREWORD

3120880

– JLG Sizzor –

c

All procedures herein are based on the use of the
machine under proper operating conditions, with no
deviations from original design intent... as per OSHA
regulations and applicable ANSI standards.

READ & HEED!

The ownership, use, service, and/or maintenance of
this machine is subject to various governmental and
local laws and regulations. It is the responsibility of
the owner/user to be knowledgeable of these laws
and regulations and to comply with them. The most
prevalent regulations of this type in the United States
are the Federal OSHA Safety Regulations*. Listed
below, in abbreviated form are some of the require-
ments of Federal OSHA regulations in effect as of the
date of publication of this handbook.

The listing of these requirements shall not relieve
the owner/user of the responsibility and obligation
to determine all applicable laws and regulations and
their exact wording and requirements, and to com-
ply with the requirements. Nor shall the listing of
these requirements constitute an assumption of
responsibility of liability on the part of JLG Indus-
tries, Inc.

1. Only trained and authorized operators shall be

permitted to operate the aerial lift.

2. A malfunctioning lift shall be shut down until

repaired.

3. The controls shall be plainly marked as to their

function.

4. The controls shall be tested each day prior to

use to determine that they are in safe operating
condition.

5. All personnel in the platform shall, at all times,

wear approved fall protection devices and
other safety gear as required.

6. Load limits specified by the manufacturer shall

not be exceeded.

7. Instruction and warning placards must be legi-

ble.

8. Aerial lifts may be field modified for uses other

than those intended by the manufacturer only if
certified in writing by the manufacturer to be in
conformity to JLG requirements and to be at
least as safe as it was prior to modification.

9. Aerial lifts shall not be used near electric power

lines unless the lines have been de energized
or adequate clearance is maintained.

10. Employees using aerial lifts shall be instructed

on how to recognize and avoid unsafe condi-
tions and hazards.

11. Ground controls shall not be operated unless

permission has been obtained from personnel
in the platform, except in case of an emer-
gency.

12. Regular inspection of the job site and aerial lift

shall be performed by competent persons.

13. Personnel shall always stand on the floor of the

platform, not on boxes, planks, railing or other
devices, for a work position.

*Applicable Federal OSHA regulations for the
United States, as of the date of publication of this
manual, include, but are not limited to, 29 CFR
1910.67, 29 CFR 1926.20, 29 CFR 1926.21, 29 CFR
1926.28, and 29 CFR 1926.453.

Summary of Contents for 3369 electric













































Reviews: