background image

SECTION 2 - PREPARATION AND INSPECTION

3120880

– JLG Sizzor –

2-5

GENERAL

Begin the “Walk-Around Inspection” at Item 1, as noted
on the diagram. Continue Left (counterclockwise viewed
from top) checking each item in sequence for the condi-
tions listed in the “Walk-Around Inspection Checklist”.

TO AVOID INJURY DO NOT OPERATE MACHINE UNTIL ALL
MALFUNCTIONS HAVE BEEN CORRECTED. USE OF A MAL-
FUNCTIONING MACHINE IS A SAFETY VIOLATION.
TO AVOID POSSIBLE INJURY, BE SURE MACHINE POWER IS
“OFF” DURING “WALK-AROUND INSPECTION”.

NOTE: Do not overlook visual inspection of chassis under-

side. Checking this area often results in discovery
of conditions which could cause extensive machine
damage.

1.

Battery Charger - No damage, properly secured.

2.

Drive Cut-out Limit Switch (3969electric) - Properly
secured, no visible damage.

3.

High Drive Cut-out Limit Switch - Properly secured,
no visible damage.

4.

Lift Cylinder - Properly secured, no visible damage,
no loose or missing parts, no evidence of leakage.

5.

Steer Cylinder - Properly secured, no visible dam-
age, no loose or missing parts, no evidence of
leakage.

6.

Wheel and Tire Assembly, Left Front - Properly
secured, no visible damage, no loose or missing
bolts.

7.

Spindle and Tie Rod, (left front) - No loose or miss-
ing parts, no visible damage, properly secured.

8.

Sizzor Arms and Sliding Wear Pads - Properly
secured, no visible damage, no loose or missing
parts.

9.

Battery Installation - Proper electrolyte level, cables
secured, no damage or corrosion. Hold-downs
secure.

10.

Safety Prop - Stored securely, no missing parts, no
visible damage.

11.

Side Cover, Hydraulic Tank - No loose or missing
parts, no visible damage, properly secured.

12.

Hydraulic Filter - No visible damage, properly
secured, no evidence of leakage.

13.

Hydraulic Reservoir - No visible damage or miss-
ing parts, no evidence of leaks. Recommended
hydraulic fluid level on level indicator on tank.
Breather cap secure and working.

14.

Drive Hub, Brake and Hub Left Rear - No loose or
missing parts, no visible damage, no evidence of
leakage.

15.

Wheel and Tire Assembly, Left Rear - Properly
secured, no visible damage, no loose or missing
bolts.

16.

Ladder - No damage, securely attached.

17.

Tilt Switch - Properly secured, no loose or missing
parts, no visible damage.

18.

Frame - No visible damage, no loose or missing
parts.

19.

Manual Descent - No visible damage, properly
secured, no evidence of leakage.

20.

Motor and Hydraulic Pump - Properly secured, no
visible damage, no loose or missing parts, no evi-
dence of leakage.

21.

Wheel and Tire Assembly, Right Rear - Properly
secured, no visible damage, no loose or missing
bolts.

22.

Ground Controls - Properly secured, no loose or
missing parts, no visible damage. Placards secure
and legible, control switches return to neutral posi-
tion. Control markings legible, manual in manual
storage box.

23.

Drive Hub, Brake and Hub Right Rear - No loose or
missing parts, no visible damage, no evidence of
leakage.

24.

Control Valve - No loose or missing parts, unsup-
ported wires or hoses, damaged or broken wires.

25.

Side Cover, Control Valve - No loose or missing
parts, no damage, properly secured.

26.

Safety Prop - Stored securely, no missing parts, no
visible damage.

27.

Controller Cover - No loose or missing parts, no
visible damage, properly secured.

28.

Battery Installation - Proper electrolyte level, cables
secured, no damage or corrosion. Hold-downs
secure.

29.

Spindle and Tie Rod Assembly (right front)- No
loose or missing parts, no visible damage, prop-
erly secured.

Figure 2-1.  Daily Walk-Around Inspection (Sheet 2 of 3)

Summary of Contents for 3369 electric













































Reviews: