background image

SECTION 5 - OPTIONAL EQUIPMENT

3120880

– JLG Sizzor –

5-1

SECTION 5.  OPTIONAL EQUIPMENT

WHEN ADDING AN ELECTRICAL OR ELECTRONIC OPTION TO
THE MACHINE, DO NOT GROUND THE DEVICE TO THE MACHINE
CHASSIS. AN ELECTRICAL OR ELECTRONIC DEVICE THAT IS
GROUNDED TO THE CHASSIS IS SEEN BY THE SEVCON AS A
SHORT CIRCUIT AND WILL CAUSE A FAULT CODE TO APPEAR.
GROUND ALL ELECTRICAL OR ELECTRONIC DEVICES TO THE
APPROPRIATE TERMINAL OF THE SEVCON CONTROLLER.

5.1

BATTERY DISCHARGE INDICATOR

The battery condition indicator is a gauge that provides a
visual indication of the condition of the batteries.

5.2

HORN

The warning horn is located on the frame of the machine,
and is controlled by a push button switch on the platform
control console. The warning horn permits the operator to
warn jobsite personnel when the machine is operating in
the area.

5.3

TRAVEL ALARM

The motion alarm horn, mounted on the frame of the
machine, provides an audible warning when the machine
is in the travel (drive) mode. It will function in forward or
reverse to warn jobsite personnel the machine is traveling.

5.4

MOTION ALARM

The travel alarm horn, mounted on the frame of the
machine, provides an audible warning when the machine
is in the drive or lift mode. It will function in forward,
reverse, lift up or lift down to warn jobsite personnel the
machine is traveling or lifting.

5.5

DESCENT ALARM

Produces an audible warning when platform lift control is
placed in the lift down position. The alarm warns person-
nel in the jobsite area to avoid the sizzor arms.

5.6

TILT ALARM WARNING LIGHT

A red warning light on the control console that lights when
the chassis is on a severe slope (over 5 degrees).

5.7

TILT ALARM

An audible warning horn that will sound when the
machine is out of level five degrees and illuminates a
warning light at the platform control station and sounds
the machine’s horn, signaling the operator.

5.8

220 VOLT RECEPTACLE

The 220 Volt dual receptacle is mounted on the platform
kick rail. The receptacle is connected to a plug on the
machine frame which can be connected to a ground
receptacle.

5.9

PLATFORM LIGHTS

Platform lights may be installed on the machine platform
rails, to provide more lighting for the operator.

5.10 NON-MARKING TIRES

For indoor use, these tires are made from a special com-
pound that, unlike regular tires, will not leave black skid
marks on floors and other surfaces.

5.11 ROTATING BEACON PLATFORM/FRAME

An amber rotating beacon may be installed under the plat-
form or on the machine frame, and is activated whenever
platform controls are selected at the platform/ground
select switch. When activated, the light provides a visual
warning of the machine’s operation.

5.12 HIGH OUTPUT BATTERIES

For increased operating power and reserve capacity, 370
amp hour batteries are available in place of the standard
245 Amp Hour batteries.

5.13 WHEEL COVERS

Provide protection for wheels and wheel bearings from
dirt, grease, mud, rocks, etc.

5.14 CYLINDER BELLOWS

A one piece accordion shaped rubber bellows may be
attached to the rod end of the cylinder barrel and the cyl-
inder rod as close to the rod attach bushing as possible.
The bellows affords protection to the cylinder rod in either
the extended or retracted position. The bellows are
installed on the lift cylinders.

Summary of Contents for 3369 electric













































Reviews: