9
8
RP3-18-GB(V1)
RP3-18-GB(V1)
BEAM A
BEAM B
For 5.0mx2.5mx1.22m(16.5’x8.2’x48”),the combination is A-B-B-C
It is absolutely essential to select a suitable site for your pool BEFORE attempting to
fill it with any water. Please select a set-up site which strictly conforms to the following
guidelines:
Guide1.
Ensure that the area is firm, flat (no bumps or mounds of earth) and extremely level, with a grade not exceeding
3° of slope at any point in the set-up area.
Guide2.
Make sure that the area you have selected to set-up the pool is completely free of sticks, stones, sharp objects or
other foreign debris.
Guide3.
Select an area that is not directly underneath overhead power lines or trees. Additionally, make sure that the pool
set-up area does not contain underground utility pipes, lines, or cables or any kind.
Guide4.
If a ground cloth is provided with your pool kit, its use is highly recommended. The ground cloth will help protect
the pool liner from damage due to weed growth, sharp objects, and debris.
Guide5.
If at all possible, choose an open location on your property that is exposed to direct sunlight. This will help to
warm your pool.
WARNING:
Pools installed on inadequately level surfaces are subject to leaking,
forming irregularities, or collapse, which can result in property damage or serious in-
jury for those in or around the pool area!
WARNING:
Do not use sand during setup process. If it appears that there is a need
for use of a “leveling agent”, then your set-up site is likely unsuitable. FAILURE TO
OBEY THIS WARNING MAY RESULT IN SERIOUS PERSONAL INJURY.
CAUTION:
Please choose your set-up area carefully, as lawn and other desirable
vegetation underneath the ground cloth(If applicable) will die. Furthermore, try to avoid
setting the ground cloth(If applicable)in areas prone to aggressive plant and weed spe-
cies, as they may grow through the ground cloth(If applicable).
CAUTION:
The pool must be accessible to a 110 or 230-volt AC outlet protected by
a Ground Fault Circuit Interrupter (GFCI). The pool should be set no closer than 2 m. to
the power source, but no further than the length of the filter pump cord. Under no cir
-
cumstances should an extension cord be used to extend the range of the connection.
+3°
Bumpy,Sloping Ground-INCORRECT
Flat,Level Ground-CORRECT
PART3-SITE SELECTION
Step4.
INSTALL HORIZONTAL BEAM
Step3.
INSTALL THE U-TUBES
Slide combined beams into sleeve,the hole on the beams should face outwards.
Slide each U-tube through the bottom addition connected belt
T-join
t
PART4-SET UP THE POOL
Step1. ACCOUNT FOR ALL PARTS.
Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled
Check each part according to “PART REFERENCE” .Make sure all the pieces to be assembled are accounted for.
IMPORTANT:
Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service
telephone number in your area.
The number of persons required for installation: 2 adult at least.
Total installation time except the time for site preparation and water filling :
45 minutes for size 13’×6.5'×39"/13'×6.8'×48"; 60 minutes for size 18’×9'×48".
For the steel frame swimming pool, no tools are required for the installation. For the filter pump (if applicable), no tools are
required for the installation.For the ladder (if applicable), the tool required for the installation is one screwdriver, one wrench.
Step2. INSTALL DRAIN VALVES COVER AND STOPPER
Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-
nection holes with the stoppers. (The out drain plug changes according to different size of pool.)
STOPPER
Out Drain Plug A
Out Drain Plug B
Drain Vavle Cover
BEAM A
BEAM B
BEAM A
For 3.0mx3.0mx1.0m(10’x10’x39.5”),the combination is A-B-A
For the short side sleeve of the pool:
For the long side sleeve of the pool:
BEAM D
BEAM E
For 3.0mx3.0mx1.0m(10’x10’x39.5”),the combination is D-E
BEAM B
BEAM C
