background image

 

 

GB - ENGLISH 

Operating Instructions 

 

Dear Customer, 

Many thanks for the confidence you have shown in us with the purchase  of  your new JET-machine. This manual has been 
prepared for the owner and operators of a JET 16-32 Plus / 22-44  Plus drum sander  to promote safety during installation, 
operation and maintenance procedures. Please read and understand the information contained in these operating instructions 
and the accompanying documents. To obtain maximum life and efficiency from your sander, and to use  the machine safely, 
read this manual thoroughly and follow instructions carefully. 

 

…Table of Contents 

1. Declaration of conformity

 

2. Warranty

 

3.  Safety

 

Authorized use 
General safety notes 
Remaining hazards 

4. Machine specifications

 

Technical data 
Workpiece dimensions 
Noise emission 
Contents of delivery 

5. Transport and start up

 

Transport and installation 
Assembly 
Mains connection 
Dust connection 
Starting operation 

6. Machine operation 

7. Setup and adjustments 

Wrapping abrasive strips 
Selecting drum abrasives 
Cleaning drum abrasives 
Drum alignment 
Conveyor belt adjustment 
Conveyor belt changing 

8. Maintenance and inspection 

9. Trouble shooting 

10. Environmental protection

 

11. Available accessories

 

 

1.  Declaration of conformity 

On our own responsibility we hereby 
declare that this product complies with 
the regulations* listed on page 2. 
Designed in consideration with the 
standards**. 
  

 

 

 

2.  Warranty 

The Seller guarantees that the 
supplied product is free from material 
defects and manufacturing faults. This 
warranty does not cover any defects 
which are caused, either directly or 
indirectly, by incorrect use, 
carelessness, accidental damage, 
repair, inadequate maintenance or 
cleaning and normal wear and tear. 

Guarantee and/or warranty claims 
must be made within twelve months 
from the date of purchase (date of 
invoice). Any further claims shall be 
excluded. 

This warranty includes all guarantee 
obligations of the Seller and replaces 
all previous declarations and 
agreements concerning warranties. 

The warranty period is valid for eight 
hours of daily use. If this is exceeded, 
the warranty period shall be reduced 
in proportion to the excess use, but to 
no less than three months. 

Returning rejected goods requires the 
prior express consent of the Seller and 
is at the Buyer’s risk and expense. 

Further warranty details can be found 
in the General Terms and Conditions 
(GTC). The GTC can be viewed at 
www.jettools.com or can be sent by 
post upon request. 

The Seller reserves the right to make 
changes to the product and 
accessories at any time. 

 

3.  Safety 

3.1 Authorized use 

This sander is designed for sanding 
wood and similar materials only. 
Sanding of other materials is not 
permitted and may be carried out in 
specific cases only after consulting 
with the manufacturer.  

The machine is not suitable for wet 
sanding. 

The proper use also includes 
compliance with the operating and 
maintenance instructions given in this 
manual. 

The machine must be operated only 
by persons familiar with its operation 
and maintenance and who are familiar 
with its hazards. 

The required minimum age must be 
observed. 

The machine must only be used in a 
technically perfect condition. 

When working on the machine, all 
safety mechanisms and covers must 
be mounted. 

In addition to the safety requirements 
contained in these operating 
instructions and your country’s 
applicable regulations, you should 
observe the generally recognized 
technical rules concerning the 
operation of woodworking machines. 

Any other use exceeds authorization. 
In the event of unauthorized use of the 
machine, the manufacturer renounces 
all liability and the responsibility is 
transferred exclusively to the operator.  

 

3.2 General safety notes 

Woodworking machines can be 
dangerous if not used properly. 
Therefore the appropriate general 
technical rules as well as the following 
notes must be observed. 

Read and understand the entire 
instruction manual before attempting 
assembly or operation. 

Keep this operating instruction close 
by the machine, protected from dirt 
and humidity, and pass it over to the 
new owner if you part with the tool. 

No changes to the machine may be 
made. 

Summary of Contents for SandSmart 16-32 Plus






















Reviews: