4
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging
the mains cord.
Remove all loose clothing and
confine long hair.
Before operating the machine,
remove tie, rings, watches, other
jewellery, and roll up sleeves above
the elbows.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit.
Use safety goggles at all times.
Use ear protection at all times.
Wear a face and dust mask when
working in a dusty environment.
Do NOT stop the abrasive wheel by
forcing the machine or by using
sideways pressure.
The material to be grinded must be
held firmly so it can not move during
the grinding operation.
Never grind pieces that are too small.
Support long work pieces with helping
roller stands.
Never place your hand near the
grinding area while machine is in
operation.
Do not perform any operation
freehand; always have the
workpiece supported by the tool
rest.
Allow the abrasive wheel to come to a
complete standstill before making
adjustments.
Do not touch the machined
workpiece until it cools or you may
be burned!
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be bolted
on a firm workbench or stand.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine when
you are tired.
Do not operate the machine under
the influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Do not allow anyone to stand behind
the unit or close to the workpiece
where debris can be thrown.
Allow the abrasive wheel to reach full
speed before grinding.
Flying sparks will occur when
grinding. They can cause injury and
ignite flammable materials.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Normal brushfire might ignite.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Do not force the power tool. It will do
a better and safer job and give you
much better service if it is used at the
rate for which it was designed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Make sure the tool operates properly.
Periodically check screws and bolts
for tightness.
Never operate with the guards not in
place – serious risk of injury!
Never stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only
Always unwind any extension cords
fully.
Damaged extension cords replace
immediately.
Do not use the power tool if the
ON/OFF switch does not turn the
power tool ON and OFF.
Make all machine
adjustments or
maintenance with the
machine unplugged from
the power source.
Use only abrasive wheels rated at
3000 RPM or higher.
Remove defective abrasive wheels
immediately.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist
The moving abrasive wheel in the
work area can cause injury.
The moving abrasive belt in the work
area can cause injury.
Broken abrasive wheel can cause
injury.
Broken abrasive belt can cause
injury.
Thrown grinding chips, dust and
noise can be health hazards.
Be sure to wear personal protection
gear such as safety goggles, dust
mask and ear protection.
Some dust and gases created by
grinding can be heath hazards.
To reduce your risk of exposure, work
in a well ventilated area.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.
Avoid body contact with earthed or
grounded surfaces (e.g. pipes,
radiators, ranges and refrigerators).
4. Machine specifications
4.1 Technical data
Abrasive wheel
Ø200x 25mm
Abrasive wheel hole dia.
Ø20mm
No load speed
2950 rpm
Abrasive belt length
1000mm
Belt width
100mm
Belt speed
15m/sec
Flat sanding platen
100x250mm
Contact wheel diameter
100mm
Dust port diameter
2x 36mm
Overall (L x W x H) 500 x 280 x 630mm
Weight
29 kg
Mains
400V ~3L/PE 50Hz
Motor power
550W S1
Reference current
1,5 A
Extension cord (H07RN-F) 4x1,5mm²
Installation fuse protection
10A
Isolation class
I
