background image

13

EGH1740 | EGH1760

7.3   CHUCK AND CHUCK MOUNTING 

(FOR D1-6 SPINDLE)

Use only high-speed chucks with these machines.

When fitting chucks or faceplate, ensure that spindle and 
chuck tapers are thoroughly cleaned and that all cams lock 
in the correct positions the first.

It may be necessary to re-set the camlock studs (A) when 
mounting a new chuck. To do this, remove the hexagon 
socket locking screws (B) and set each stud so that the 
scribed ring (C) is flush with the rear face of the chuck - 
with the slot - lining up with the locking screw hold.

Now mount the chuck or faceplate on the spindle nose and 
tighten the six cams in turn.

When fully tightened, the cam lock line on each cam 
should be between the two V marks on the spindle nose.

If any of the cams do not tighten fully within these limit 
marks, remove the chuck or faceplate and readjust the 
stud as indicated in the illustration.

Fit and tighten the locking screw (B) at each stud before 
remounting the chuck for work. A reference mark should 
be made on each correctly fitted chuck or faceplate to 
coincide with the reference scribed on the spindle nose. 
This will assist subsequent remounting.

Note: Do not interchange chucks or faceplates 
between lathes without checking for correct cam 
lock.
Take careful note of speed limitations when using 
faceplates; 12 inch faceplates should not be run 
at speeds higher than 1000 rev/min. and 14 inch 
faceplates should not be run at speeds higher 
than 770 rev/min.

Fig. 10

Cam lock line between arrows

Turn stud in one turn

Cam release datum

A C

B

Detail of camlock stud 

ass’y

7.4  LUBRICATION CHECKS

Headstock/Gearbox/Carriage, Apron/Tailstock

Before operating the machine, make the following 
important checks:

• 

 The headstock is filled to the correct level with 11.5 
liters of R-32 oil, or equivalent. Check oil weekly and 
change the oil every 6 months.

• 

 The gearbox is filled to the level marked on the oil 
sight window with 1.8 liters of R-68 oil, or equivalent. 
Check oil weekly and change the oil every year.

• 

 The carriage apron is filled to the level marked on 
the oil sight window with 1.8 liters of R-68 oil or 
equivalent. Check oil weekly and change the oil 
every year. 

• 

 In addition, using an oil can, apply oil to the points  
shown on lubrication diagram which require daily 
oiling. Use light machine oil or way lubricant.

• 

 Before each working shift, operate the one shot 
lubrication pump to ensure adequate lubrication of 
carriage slideways. 

A manually operated one shot lubrication pump (A) is 
incorporated into the apron. It enables the operator to 
ensure that the slideways are kept adequately lubricated. 
The pump should be operated before and occasionally 
during the work period.

Turn stud out one turn

Reference mark on spindle nose and chuck

Summary of Contents for 892100





































































Reviews: