background image

 

 January, 2009 

 

1 Safety Information 

The 

JET CENTRAL  TURBINE ENGINES

 are in its own right  a single stage centrifugal flow 

gas turbine engine, configured to operate as a 

TURBOJET ENGINE 

for use mainly, but not 

exclusively,  in  remotely  piloted  fixed  wing  aircraft.  Such  aircraft  and  their  control  systems 
must be appropriately designed and constructed to be compatible with the performance of the 

TURBOJET ENGINE.

 

NOTE: 

The airworthiness, structural design, integrity of the aircraft and its control systems 

are the entire responsibility of the owner/builder/operator. JET CENTRAL 

and its agents 

cannot accept responsibility for any failure, structural or otherwise, of the aircraft or its control 
systems. 

JET CENTRAL 

and its agents cannot accept responsibility for any inappropriate or 

unauthorized use of the 

JET CENTRAL ENGINE. 

The 

JET  CENTRAL 

gas  turbine  engine  is  a  very  safe,  easy  to  operate  unit.  The 

JET 

CENTRAL 

is  a  state  of  the  art  gas  turbine  engine  and  all  components  are  manufactured 

within the highest standards. If operated correctly it will provide years of reliable, trouble-free 
service, with low maintenance. 

It cannot however, be stressed highly enough, that the operating instructions be fully 
understood  before  attempting  to  operate  your  engine.  Any  alterations  to  the  engine 
whatsoever,  without  the  written  consent  of  JET  CENTRAL,  will  render  any  warranty 
null and void and as a consequence the controlling body in your country may not grant 
approval for use. 

The 

JET  CENTRAL 

gas  turbines  are  high  performance 

TURBOJET  ENGINES

  that  need 

discipline,  commitment  to  correct  and  safe  operation.  With  other  persons  present  while 
operation, the 

TURBOJET ENGINE

 

ALWAYS ENFORCE THE PROPER SAFE DISTANCES 

FROM THE TURBINE!  

 

The recommended minimum safe distances are: 

 

In front of the turbine: 

15 feet 

 

Beside of the turbine: 

 25 feet 

 

Behind the turbine:   

25 feet 

 

Fire  extinguishers  should  be  on  hand  at  all  times. 

JC 

recommends  CO

2

  variety.  To  avoid 

hearing  damage,  always  use  hearing  protection  when  near  a  running  turbine  engine. When 
the turbine is running never place your hands closer than 6 inches into the area of the intake.  

An  EXTREME  SUCTION,  which  can  grasp  a  hand,  fingers  or  other  objects  in  a  flash, 
prevails in this area. Be aware of this danger always!  

 

Summary of Contents for Rabbit













































Reviews: