background image

4

Tools and Parts

Gather the required tools and parts necessary for correct 

LP gas conversion.

Tools needed

 

Flat-blade screwdriver

 

3

/

32

" (#0 [2.0 mm]) flat-blade screwdriver (Screwdriver 

shaft must be a minimum of 2

1

/

2

" [6.4 cm] long.)

 

Adjustable wrench

 

7.0 mm nut driver

 

7.0 mm wrench

Parts supplied

 

LP orifice package (W10686634)

 

Conversion label (W10590570)

High Altitude Conversion

To convert the cooktop for elevations above 6,560 ft 

(1999.5 m), order a High Altitude Conversion Kit.

 

Part Number W10686630 - LP high altitude

 

Part Number W10686629 - Natural gas high altitude

To order, see the “Assistance or Service” section of the 

Use and Care Guide.

IMPORTANT: 

Gas conversions from Natural gas to LP gas 

must be done by a qualified installer. Before proceeding with 

conversion, shut off the gas supply to the cooktop prior to 

disconnecting the electrical power.

Convert from Natural Gas 

to LP Gas

1. 

Turn manual shutoff valve to the closed position.

2. 

Unplug cooktop, or disconnect power.

To Convert Gas Pressure Regulator

WARNING

This conversion kit shall be installed by a 

qualified service agency in accordance 

with the manufacturer's instructions and 

all applicable codes and requirements of 

the authority having jurisdiction. If the 

information in these instructions is not 

followed exactly, a fire, explosion or 

production of carbon monoxide may 

result causing property damage, personal 

injury or loss of life. The qualified service 

agency is responsible for the proper 

installation of this kit. The installation is 

not proper and complete until the 

operation of the converted appliance is 

checked as specified in the 

manufacturer's instructions supplied with 

this kit.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure 

gas pressure does not exceed 14" (36 cm) water 

column. 
Examples of a qualified person include: 
licensed heating personnel, 

authorized gas company personnel, and

authorized service personnel.
Failure to do so can result in death, explosion, or fire.

A

B

C

A.  To cooktop
B.  Shutoff valve (closed position)
C.  Gas supply line

A

B

C

D

A.  Access cap
B.  Rear of cooktop
C.  Gas pressure regulator
D.  Gas flow

Summary of Contents for JGC2530E Series





















Reviews: