JEI SteelBeat PRO PB10 Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 35

background image

PB10 (PBE)

This document is protected by copyrights.

Copying, using, or distributing without permission of JEI Group Ltd is prohibited.

8

21. After every use, remove chips and excess coolant from

the

machine.

Never

remove

chips with bare hands. Clean the machine with a cotton cloth without

using any chemical agents.

22. Cover steel parts with a thin anti-corrosion coating to protect the machine from

rust when not in use for any extended period.

23. Maintain the machine and install/remove parts and tools only when the machine

is unplugged from the air (power) source.

24. Repair only in a service center appointed by the seller.

25. If the machine falls from any height, is wet, or has any other damage that could

affect the technical state of the machine, stop the work and promptly send the

machine to the service center for inspection and repair.

26. Never leave the machine unattended during work.

27. Remove from the worksite and store in a secure and dry place when not in use,

previously removing the tools from holders.

«
...
6
7
8
9
10
...
»

Summary of Contents for SteelBeat PRO PB10




































Reviews:

No comments

Related manuals for SteelBeat PRO PB10

Brand: Makita Pages: 15

Brand: Makita Pages: 12

Brand: Nation Flooring Equipment Pages: 2

Brand: NARGESA Pages: 71

Brand: C-SCOPE Pages: 44

Brand: Porter-Cable Pages: 15

Brand: Air & Allied Sales Pages: 11

Brand: Gardner Denver Pages: 27

Brand: Akyga Pages: 4

Brand: Hama Pages: 48

Brand: Linear Technology Pages: 6

Brand: jbc Pages: 2

PSI 8000 3U HS PV Series

Brand: Elektro-Automatik Pages: 76

Brand: Dawson Pages: 63

Brand: Neilsen Pages: 8

Brand: Baileigh Pages: 39

Brand: Kerbl Pages: 15

Brand: REED Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands