Inspect the valves and plugs for scratches, burrs,
nicks, or scores. Minor surface scratches on steel
valves and plugs can be removed with crocus cloth
but do not round off the edges of the valve or
plug lands. Maintaining sharpness of these edges is
vitally important. The edges prevent foreign matter
from lodging between the valves and plugs and the
bore.
Inspect all the valve and plug bores in the valve
body. Use a penlight to view the bore interiors.
Replace the valve body if any bores are distorted or
scored. Inspect all of the valve body springs. The
springs must be free of distortion, warpage or broken
coils.
Check the two separator plates for distortion or
damage of any kind. Inspect the upper housing,
lower housing, 3-4 accumulator housing, and transfer
plate carefully. Be sure all fluid passages are clean
and clear. Check condition of the upper housing and
transfer plate check balls as well. The check balls
and ball seats must not be worn or damaged.
Trial fit each valve and plug in its bore to check
freedom of operation. When clean and dry, the valves
and plugs should drop freely into the bores.
Valve body bores do not change dimensionally with
use. If the valve body functioned correctly when new,
it will continue to operate properly after cleaning and
inspection. It should not be necessary to replace a
valve body assembly unless it is damaged in han-
dling.
The only serviceable valve body components are
listed below. The remaining valve body components
are serviced only as part of a complete valve body
assembly. Serviceable parts are:
•
dual solenoid and harness assembly
•
solenoid gasket
•
solenoid case connector O-rings and shoulder
bolt
•
switch valve and spring
•
pressure adjusting screw and bracket assembly
•
throttle lever
•
manual lever and shaft seal
•
throttle lever shaft seal, washer, and E-clip
•
fluid filter and screws
•
detent ball and spring
•
valve body screws
•
governor pressure solenoid
•
governor pressure sensor and retaining clip
•
park lock rod and E-clip
ZG
TRANSMISSION AND TRANSFER CASE
21 - 97
CLEANING AND INSPECTION (Continued)
Summary of Contents for 1997 Grand Cherokee
