JCM GLOBAL Taiko PUB-7 Manual Download Page 16

Page: 16 / 20

Part No. 960-100919R_Rev. 1

1 6

March, 2017

JCM Training Overview

Taiko™ Banknote Validator

DOWNLOADING SOFTWARE

Software Downloading to a Taiko

™

Unit can be performed from a PC or a

DT-200 BlueWave 2.0

™

Download Tool.

PC S

OFTWARE

OADING

To download Taiko

™

Software using a PC containing a Windows Operating

System, proceed as follows:

1. Set DIP Switches #1, #7 and #8 to ON.
2. Using Harness Type “B”, connect from the PC Serial Port to the 4-pin Maint-

enance Connector on the Taiko

™

Unit.

3. Apply power to the Taiko

™

Unit, The

GREEN

LED will begin to flash steadily.

4. Open the

WBA/DBV Download Application

(downloadable from

www.jcm-

global.com

5. Set the Baud Rate to 38400, and select an available Comm Port on the PC.
6. Select the file to be downloaded using the “

Browse

” function on the PC.

7. Mouse-click on “

Start Download

”. The

YELLOW

LED will light steady.

8. The Download Program Screen will show a download progress bar.
9. When the download is complete and the CRC is verified, the

BLUE

LED will

light. The download is now complete.

LUE

AVE

2.0

™

OFTWARE

PDATE

To update BlueWave 2.0

™

Software, proceed as follows:

1. Ensure the

PUB

software file is located in the

DOWNLOAD

folder on the SD

Card.

2. Insert the SD Card into the BlueWave 2.0

™

Handheld Download Tool.

3. Connect the BlueWave 2.0

™

Download Tool to the PUB/EBA Adapter.

4. Connect the PUB/EBA Adapter to the

PUB-7/11 Unit

5. Set DIP Switches #1, #7 and #8 to ON.

6. Apply power to the Taiko

™

PUB-7/11

Unit.

7. Slide the

Power ON/OFF Switch

on the BlueWave 2.0 Download Tool to

8. When the Top LED on the BlueWave 2.0 Download Tool turns

GREEN

, press

the

LOAD

Button.

9. When all three LEDs on the BlueWave 2.0 Download Tool turn

GREEN

, the

program download is complete.

10.Remove power from the

PUB-7/11

Unit. Disconnect the Download Harness and

reset DIP Switches to their standard settings for normal operation.

NOTE: Refer to the Taiko Unit Parts List on page 19 for the correct
harness.

NOTE: Refer to the BlueWave 2.0™ Download Tool Operator Guide
(JCM P/N 960-100924R) for details on Downloading Software and
Updating a PUB-7/11 Validator.

Summary of Contents for Taiko PUB-7





















Search results

Summary of Contents for Taiko PUB-7

Reviews:

Related manuals for Taiko PUB-7

Brands by name

Popular brands

JCM GLOBAL Taiko PUB-7, Manual

Search results

Summary of Contents for Taiko PUB-7

Reviews:

Related manuals for Taiko PUB-7

Brands by name

Popular brands