![background image](http://html1.mh-extra.com/html/jcm-global/ivizion-series/ivizion-series_operation-and-maintenance-manual_3543287036.webp)
P/N 960-100929R_Rev. 3 {EDP #148849}
© 2012, Japan CashMachine Co., Limited
2 - 8
Section 2
iVIZION® Series Next-Generation Banknote Acceptor Unit
Installation
Preventive Maintenance
R
ETRIEVING
B
ANKNOTES
To retrieve Cash Box deposited Banknotes perform
the following steps:
1. Release the Cash Box from the Frame and pull it
forward.
2. Unlock the Cash Box with a User supplied Key.
3. Open the Cash Box Door and retrieve deposited
Banknotes as illustrated in Figure 2-5.
C
LEARING
A
B
ANKNOTE
J
AM
To retrieve a jammed Banknote jammed inside the
Banknote Acceptor Head Part proceed as follows:
1. Open the Acceptor Unit’s Upper Guide by press-
ing in on the two (2) Upper Guide Access Buttons
Blue
Arrows) located on each
side of the Upper Guide, and lift the Acceptor top
up and open and remove the jam.
2. Remove the jammed Banknote. If the jammed
Banknote is not found in the Acceptor Unit, then
3. Open the Transport Unit’s Upper Guide by press-
ing in on the Upper Guide Access Lever
b
single
Blue
Arrow) located in
the center of the Upper Guide, and lift the Trans-
port Section up and open and remove the jam.
4. If the jammed Banknote is not found in the higher
Sections, pull the Cash Box out of the Frame
(See Figure 2-7 a). Check at the rear side of the
Frame and remove the jammed Banknote located
there if any (See Figure 2-7 b).
5. A jammed Banknote may also be present on top
of the Cash Box; remove it if present at this
location (See Figure 2-7 c).
Table 2-11
iVIZION SS/LD Bezel JPL (CN7) Connection Pin Assignments
Front Side View
Box Pin Header (Control CPU Board Side): A3B-8PA-2DS (71) (HRS) JCM Custom
Socket Housing (Bezel Side): A3B-8D-2C (HRS)
Contact Type (Bezel Side): A3B-2630SCFC (HRS)
Polarizing Pin: A3-GPIN (HRS)
*
Recommended Wire: UL1007 AWG#24~30
Pin No.
Signal Name
I/O
†
Function
1
JP+
IN/OUT -
2
-
-
Polarizing Pin Key
3
JP-
IN/OUT -
4
5V DC
OUT
5V DC Power Supply (Maximum 300mA)
5
VIN
OUT
LED Drive Power Supply 12V DC/24V DC (Maximum 300mA)
6
GND
SG
-
7
LED POWER
OUT
LED Power Supply 5V (Maximum 20mA Current Limitation
Resistance)
8
LED 1
IN
LED Drive Line (cathode) Maximum Sink Current: 300mA
*. Caution: The Embossed Numbers located on the Polarizing Pin Connector, and on the CN7 Connector Numbers indicated in Table 17 are different. The Polarizing Pin Key
should be inserted into Pin Position No.4 of the Polarizing Pin Connector.
†. I/O (Input/Output) Terminal as viewed from outside the Banknote Acceptor.
C
ONNECTOR
P
IN
A
SSIGNMENTS
(C
ONTINUED
5)
Table 2-11 lists the iVIZION SS/LD Bezel Connector Pin Assignments.
CN7
Polarizing Pin
ID Pin No.4
Connector
Embossed
Remove
Figure 2-5
Retrieving Banknote
a
) Acceptor Unit Upper Guide Access Lever
b
) Transport Unit Upper Guide Access Lever
Open
Open
b
a
Remove
Remove
Hidden
Figure 2-6
Open the Upper Guides