background image

 

A WILKINSON STAR LIMITED PRODUCT                                                                                                                                    12-16 ISSUE 1 

Your new product 

Thank you for selecting this Jasic Technology, Wilkinson Star product. 

This product manual has been designed to ensure that you get the most from your new product. Please 
ensure  that  you  are  fully  conversant  with  the  information  provided  paying  particular  attention  to  the 
safety  precautions.  The  information  will  help protect  yourself  and others  against  the  potential hazards 
that you may come across. 

Please ensure that you carry out daily and periodic maintenance checks to ensure years of reliable and 
trouble free operation. 

Wilkinson Star Limited are a leading supplier of equipment in the UK and our products are supported by 
our extensive service network. Call your distributor in the unlikely event of a problem occurring. Please 
record  below  the  details  from  your  product  as  these  will  be  required  for  warranty  purposes  and  to 
ensure you get the correct information should you require assistance or 

spare parts. 

 

Date purchased ________________________________________ 

From where       ________________________________________ 

Serial Number   ________________________________________ 

(The serial number will normally be located on the equipment data plate on the top or underside of the 
machine ) 

 

 

 

 

Disclaimer 

Whilst  every  effort  has  been  made  to  ensure  that  the  information  contained  within  this  manual  is 
complete and accurate, no liability can be accepted for any errors or omissions. Please note products are 
subject to continual development and may be subject to change without notice. 

 

 

This  manual  should  not  be  copied  or  reproduced  without  the  written  permission  of  Wilkinson  Star 
Limited 

 

Summary of Contents for CUT80 (L205)

















Reviews: