background image

 

A WILKINSON STAR LIMITED PRODUCT                                                                                                                                    12-16 ISSUE 1 

TECHNICAL PARAMETERS 

 

CUT 60 (JP-61) 

CUT 80 (JP-81) 

RATED INPUT POWER SUPPLY 

3 PHASE 400V 50/60 Hz 

3 PHASE 400V 50/60 Hz 

RATED INPUT CAPACITY (KVA) 

10.8 

14.4 

POWER FACTOR 

0.7 

0.7 

RATED OUTPUT (A/V) 

60/104 

80/112 

RATED DUTY CYCLE (%) 

40 

40 

NO LOAD VOLTAGE (V) 

310 

310 

ARC IGNITION MODE 

|NON HF 

NON HF 

POST AIR FLOW (S) 

10 

10 

AIR PRESSURE (BAR) 

4.5 

4.5 

INSULATION GRADE 

PROTECTION CLASS 

IP 21S 

IP 21S 

EFFICIENCY (%) 

85 

85 

MACHINE DISPOSAL 

Please do not dispose of electrical waste with normal waste products. 

In accordance with the European directive 2002/96/EC regarding waste electrical and electronic equip-
ment abnd its implementation into national law any electrical or electronic which has reached its end 
of life must be collected separately and disposed of via a suitable recycling facility. 

The owner of the equipment is required to return the equipment to a suitable recycling facility or to 
Wilkinson Star  Limited for the correct recycling of the product. 

Summary of Contents for CUT80 (L205)

















Reviews: