Jasic AC/DC250P Schematic Diagram Download

Page: 12 / 18

5. Turn on the machine, and it

appears normal, press the

welding torch switch and there

is gas out, the malfunction LED

is on. Turn to ARC mode, the

malfunction LED turns on.

a. Over-current protection occurs when

welding is carried out.

b. Over-heating protection occurs when

welding is carried out.

c. Some parts on top PCB, center PCB, or

bottom PCB are damaged.

a. Turn off the machine for 5mins

and restart.

Stop the welding operation for

5mins, or the secondary inverter

thermal switch is damaged.

c. Check. Turn off the machine, pull

out the connecting cable matching

the socket CON2 on top PCB

PM-04-A3 with the socket CON1

on HF PCB PZ-35-B0, turn on the

machine. If the malfunction LED is

off, the transformer T1 on HF PCB

is short-circuited or damaged. If

it’s on, turn off the machine, pull

out the connecting cable matching

socket CON1 on top PCB

PM-04-A3, turn on the machine. If

the malfunction LED is on,

MOSFET U1-U24 on top PCB or

some part on drive module

PK-08-A1 is damaged; if it’s off,

transformer T1/T2/T3/T4 or

rectifying diode U1/U24 on center

PCB PD-13-B0 is damaged.

Summary of Contents for AC/DC250P



















Search results

Summary of Contents for AC/DC250P

Reviews:

Related manuals for AC/DC250P

Brands by name

Popular brands

Jasic AC/DC250P, Schematic Diagram

Search results

Summary of Contents for AC/DC250P

Reviews:

Related manuals for AC/DC250P

Brands by name

Popular brands