Japan Cach Machine J3500E Owner'S Manual Download Page 117 | Manualshive

Page: 117 / 123

background image

111

111

All clear reset could not therefore be executed.

E169 - Dip switch 1 OFF

- It indicates that an operation from keyboard
  (Reset) that request the setting in "ON"
  position of the Switch 1on ECR's mother board
  is being executed without Switch 1 in "ON"
position.

E171 – Not authorized

- It required supervisor operation.

E172 - Dep-Shift error

- It indicates that the use of the "SHIFT" has
  defined the amount recording on a department
  upper than "50", or the PLU on PC
  makes reference to a dept. upper than "50".

E173 - Amount not Allow

- The inserted amount is not allowed.

E175 - Receipt buf full

- Indicates that the buffer used to containing
  the operations made in the within of a receipt
  it has caught up the 99 lines ; if the receipt it
  comes continued, the receipt VOID will not
  be more possible and the eventual double
  receipt could not be detailed.

E177 - HALO (RM/VD)

- It indicates that the value of the amount input
  for the execution of the VOID or R.M. operation
  is upper to the maximum allowed from the
  configuration of the ECR.

E178 - LALO (RM/VD)

- It indicates that the value of the amount input
  for the execution of the VOID or R.M. operation
  is lower to the maximum allowed from the
  configuration of the ECR.

E179 - Mode cannot chg.

- It indicates that it has been tried to change
  the key position with the receipt open ; this
  message can appear in mechanical key
  moving case (if present like option), or because
  the key "key" has been pressed with
  the receipt in course.

E180 - subtotal HALO over

-It indicates that it has been exceeded the
maximum amount in one receipt.

E183 - inhibit display

- It indicates that it is being tried to execute a
report in visualization on the display, while the
ECR is set in order to doesn't allow such type
of report.

E184 - inhibit double multi

- It indicates that it has been executed an
  operation of "double multiplication" (Es.:
  10--X--10--X--500) while in the ECR the operation
  is not allowed.

E185 - inhibit P-T-D reset

- It indicates that it is being tried to execute a
P-T-D reset while on ECR this kind of reset
Isn't allowed.

E186 – no PLU memory

- It indicates that on ECR there isn’t memory
et for PLU containing.

E187 – no PB memory

- It indicates that on ECR there isn’t memory set
For PB containing.

E189 - SLIP not connect

- It indicates that it has been activated the Slip
without that the same one is
connected to the ECR or with the Slip Printer
In "OFF" condition.

«
...
115
116
117
118
119
...
»

Summary of Contents for J3500E




























































































































Reviews:

No comments

Related manuals for J3500E

MET ONE 3400 Series

Brand: Hach Pages: 118

Brand: SESTOS Pages: 2

Brand: Aimco Pages: 36

Brand: Precision Digital Corporation Pages: 98

Brand: Velleman Pages: 7

Brand: Red Ion Pages: 4

Brand: Alberici Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands