Japan Cach Machine J3500E Owner'S Manual Download Page 57 | Manualshive

Page: 57 / 123

background image

51

51

7.48 WARNING WORKING MODE

P (43X) X/time (AB)

Sub Total #/NS

KEY

X : alarm code to define (from 1 to 4)
1 =Programmable alarm N.1
2 =Programmable alarm N.2
3 =Programmable alarm N.3
4 =Programmable alarm N.4
A : 0 =normal acoustic signal

1 =buzzer three times for minute

B : 0 =yes Time on Display

1 =no Time on Display

Note :

⇒

in case of 0 A= normal acoustic signaling, the signaling will have the

duration defined on par. 7.47 to the point "S S".

7.49 PERSONAL REPORT PROGRAMMING

It's possible to define until four different groups of personal report, with everyone of

which it'll be possible to obtain, in automatic mode until five different reports (between
those available on the ECR and indicated in the following table to par. 7.49.1 of the
following page), they will be printed by the input of a single code of report (from 2 to 5, that
one of the personal report chose).
  Thanks to this function it will be possible, as an example, to have in automatic mode
the reports that normally come executed on the ECR without to have to remember all the
codes.
    The personalized reports can be executed in "X" mode and also in "Z" mode.

  P        (50R)          X/time

(AAA)

X/time

(BBB)

X/time

(CCC)

X/time

(DDD)

X/time

(EEE)

Sub

Total

#/NS

R

:    number of the personal report to be programmed (from 2 to 5), the
      same number will be used in "X" or "Z" for the execution of the
   personal report.

AAA

:

number of the first report to link to personal report

BBB

:

number of the second report to link to personal report

CCC : number of the third report to link to personal report
DDD

: number of the fourth report to link to personal report

EEE : number of the fifth report to link to personal report
Note :

⇒

at the "personal Reports" is possible to link quite all the reports available in

the ECR except :

1

Another personal Report

2

A code of individual report (therefore the reports with

code that begins with 4xx and/or 5xx)

3

A code of sequential report (therefore the reports with

code that begins with 6xx and/or 7xx)

⇒

if in a personal report it is necessary to insert less than 5 reports, to directly

press SUB-TOTAL key after the insertion of the last report code without to
confirm by the "X/time" key.

«
...
55
56
57
58
59
...
»

Summary of Contents for J3500E




























































































































Reviews:

No comments

Related manuals for J3500E

Brand: Garland Pages: 32

Brand: Nautilus Hyosung Pages: 22

Brand: Sam4s Pages: 271

Brand: Olivetti Pages: 3

Brand: IBEST Pages: 4

Electronic cash register

Brand: Sam4s Pages: 81

Brand: Sam4s Pages: 141

Brand: Sam4s Pages: 208

Brand: Sam4s Pages: 271

Brand: RCH Pages: 62

PHYSICS 1003122

Brand: 3B SCIENTIFIC Pages: 8

Brand: Wincor Nixdorf Pages: 37

Brand: Labelmate Pages: 61

Brand: Magner Pages: 26

Brand: Sam4s Pages: 2

Brand: LAUREL Pages: 25

FlexPay Encrypting PIN Pad

Brand: GILBARCO VEEDER-ROOT Pages: 86

Brand: Nautilus Hyosung Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands