background image

Technical data

Rotor Ø 

ca. 705 mm

Length 

ca. 645 mm

Height 

ca. 230 mm

Weight 

ca. 800 g (RTF)

Channel 

6 Kanal

Motor Brushless

3

Accessories

battery charger 

  X-Peak 3 EVO 

 

Art.-Nr. 15 2030

Already assembled in Helicopter

Servos

  

 

 

Ord. No.

 

03 1791 (only ARF &  RTF)

Gyro

  

 

 

Ord. No.

 

03 1798

Controller

 

 

flight control system E-Rix 450

  

Ord. No. 03 1792

Motor  

Brushless E-Rix 450 

  

Ord. No. 03 1793

Rotorblades

  

GFK 325 mm

  

 

Ord. No.

 

03 1794

Battery

 

Lipo Sun V2 2200 mAh 30 C 

 

Ord. No.

 

14 1298 (only RTF)

Transmitter with 6-ch 2,4 GHz transmitter 

 

Ord. No.

 

06 1180 (only RTF)

Box contents

• Alu chassis
• Alu main rotor head
• GfK Main rotors 

(only ARF & RTF)

• Alu tailunit
• GfK Canopy 

(only ARF & RTF)

• 6-ch 2,4Ghz System (only RTF)
• small parts

• 

Instructions

Certificate of Conformity

Certificate of Conformity 

JAMARA e.K. hereby declares that the model‚ ‘‘Alvis‘‘ follows the 

appropriate and relevant EEC Directives, in particular those listed 

below and that the model has been constructed accordingly.

 

Set incl. transmmitter and receiver

For questions in regarts to the conformity, 
please contact our service.

Jamara e. K.
Inh. Erich Natterer
Am Lauerbühl 5
DE-88317 Aichstetten
Tel. +49 (0) 7565/9412-0
Fax +49 (0) 7565/9412-23
www.jamara.com  - [email protected]

Further information can also be found at 
www.jamara.com - Downloads - Konformitätserklärung.

Relevant EEC Directives:

Radio & Telecom Terminal Equipment (R&TTE) 1999/5/EU

Waste Electrical and Electronic Equipment (WEEE) 2002/96/EU

  

Restriction of Hazardous Substances (RoHS) 2002/95/EU

X

X

X

Summary of Contents for E-Rix 450





















Reviews: