background image

R

K

AIL ING

By MTH Electric Trains

®

NYC Dreyfuss 4-6-4

STREAMLINED STEAM ENGINE

OPERATING INSTRUCTIONS

  Thank you for purchasing the RailKing Die-Cast NYC Dreyfuss 4-6-4 steam engine.  The
engine’s die-cast body and tender are traditionally sized for operation on any O-27 layout.
The engine is compatible with any standard AC transformer, (see page 25 for a complete
list of compatible transformers and wiring instructions), and is completely compatible with
most 3-rail locomotives, rolling stock and accessories.  

  The locomotive and tender are equipped with either an electronic whistle or the
ProtoSound Digital Sound and Train Control System which contains several deluxe
features that are simple and fun to operate.  Each feature is described  among the following
pages which should be read before the engine is operated.  For those of you who can’t wait
to get started, the Quick Start Operating Instructions found on Page 3 should be read so
that you understand the basics of the operating system.  Please note that some features
are only found in the ProtoSound equipped engines and are marked as such.  Features not
marked as ProtoSound are available in both versions.

Summary of Contents for NYC Dreyfuss 4-6-4




























Reviews: