background image

page: 3 / 20

2.

Use and Maintenance instruction

2.1.

General

CAUTION!

For the reasons of safety, installation, maintenance and use of
awnings, please follow the following guidelines.

The installation of the awning should be done by an authorized dealer.

Modifying the construction of the awning are not allowed.

The arms are under high spring tension. Do not try uncouple of the spring arms.

It is not be allowed to under awning be during maintenance or installation work.

Follow rules and instructions on health and safety during installation and maintenance.

Handle uncouple after use.

Do not use an awning near an open flame.

Use the manual control of awnings with drive in emergency only.

Do not overload an awning construction.

Roll up the awning in bad weather such as frost, snow, rain and hail.

2.2.

The right use

Awning is designed to protect against sunlight. The System allows the user to unroll or roll up her as
necessary.

For a manual control, the system based on a crank and gearbox.

By turning the handle in both directions, an awning can be roll up or unroll.

By folding arms awning turn the crank until the awning sheathing will be tight enough. It is not

allowed to unroll the fabric from the roller tube completely.

For the Electric drive the system is made of an electric motor and a control switch (it can a wall

switch, remote control, and/or weather automatic be).

The Awning is not designed for the other purposes (eg. protection against other weather conditions).

CAUTION!

Roll up the awning in bad weather such as frost, snow, rain and hail.

2.3.

Information regarding products with electrical supply

CAUTION!

Do not leave children alone with the device that controls the awning. Keep the remote
control away from children..

If the awning is equipped with an electric motor or lighting, the manual provides:

An electric circuit diagram that can be used during the installation, together with assembly

instructions.

Certification of electrical components delivered for the awning.

CAUTION!

One should check the electrical wiring two times a year for signs of wear or damage to
the cable. Do not use if they need to be repaired.

Summary of Contents for Jupiter





















Reviews: