JAI GO-5000C-PGE, User Manual

Page: 65 / 70

GO-5000M-PGE / GO-5000C-PGE
- 63 -
Acquisition mode
Continuous / Single Frame / Multi Frame (1
～
255)
Trigger Selector
Acquisition Acquisition Start/ Acquisition Stop
Exposure Frame Start
Transfer
JAI Frame Transfer
Exposure mode OFF, Continuous, Timed (EPS), Trigger Width
Trigger option
OFF / RCT (with ALC function)
Trigger Overlap
Fixed (Readout)
Trigger Input Signal
Line 6 (Opt In), Software, PG0, NAND Out 0/1, Action 1/2
Opt. Filter
5 steps (10 µs (Typ), 100 µs, 500 µs, 1ms, 5ms, 10ms)
Exposure
Mode
Timed
Exposure Auto: OFF 10 μs (Min.)
～
8 second (Max.) (Note1), Variable unit:
1 μs
Exposure Auto: Continuous 10 µs (Min.)
～
8 second (Max.)( Note1),
Variable unit: 1 μs
Trigger Width
10 μs (Min.Note1)
～ ∞
(Max.) (Note1)
Exposure Auto OFF / Continuous
Auto Exposure Response Speed
1
～
8
Video Send mode
Normal ROI, Multi ROI (1 to 5), Trigger sequence, Command sequence,
Delayed readout
Digital I/O
Line Selector (6P): GPIO IN / GPIO OUT
Black
Level
Adjust.
Ref. level
33.5LSB 10-bit (Average value of 100*100)
Video level adj. range
0
～
100 10-bit
Adj. range
±
64LSB against Ref. level 10-bit
Resolution
1 STEP = 0.25LSB
Analog Base Gain (For manual)
0dB, 6dB, 12dB 0dB, 6dB, 12dB (R/G/B individual setting)
Gain
Control
Manual
Adj. range
0dB
～
+24dB (Note2)
1 step=x0.01 (0.005dB to 0.08dB)
Varies by setting value
0dB
～
+24dB (Note2)
1 step=x0.01 (0.005dB to 0.08dB)
Varies by setting value
Gain Auto OFF / Continuous OFF / Continuous
WB Gain — R / B : -7dB to +15dB, 1 step = 0.01dB
WB Area —
4 x 4
WB Range —
3000K
～
9000K
White Balance — OFF, Continuous, Once
Blemish
Comp.
Detection
Detect white blemish above the threshold value
(Black blemish is detected only by factory )
Compensation Complement by adjacent pixels (Continuous blemishes are not compensated)
Numbers 256 pixels
ALC AGC and auto exposure can be combined and automatically controlled
Gamma 0.45, 0.6 and 1.0 (OFF) (3 steps are available)
Dark compression Choice of Linear or Dark compression ON
LUT OFF: γ=1.0, ON=32 points (Mono), 16 points (Bayer) can be set
HDR 4 settings, Level 1, 2, 3 and 4 —
Power
6-Pin
Connector
Input range
DC+12V to +24V ± 10% (At the input terminal)
Current
190mA
±
20mA (At 12V input, Full pixels) (Typical)
Power
2.5W (At 12V input, Full pixels) (Typical)
PoE
Input range
DC 35
～
57V
Current
58mA
±
6mA (At 55V input, Full pixels) (Typical)
Power
3.0W (At 12V input, Full pixels) (Typical)
Lens mount
C mount Rear protrusion of the lens is less than 10 mm