JAI CB-140GE User Manual Download Page 48

Page: 48 / 76

CM-140GE / -RA/-UV / CB-140GE / -RA

- 46 -

10.2.3 Pulse Width Control trigger mode
In this mode the accumulation time is equal to the trigger pulse width. Here it is possible to have

a long time exposure. The maximum recommended time is <2 seconds.

The accumulation can be LVAL synchronous or LVAL asynchronous.

The resulting video signal will start to be read out after the trigger rising edge.

For timing details, refer to fig. 19 through fig. 24 and fig. 30 through 31.

To use this mode:

Important notes on using this mode



Trigger pulse width >2 LVAL to <2 seconds



The following table shows minimum trigger interval in synchronous accumulation mode

Full scan

1055 L

1/2 Partial

821 L

2/3 Partial

705 L

1/4 Partial

531 L

1/8 Partial

445 L

V Binning

530 L

In case of asynchronous mode, the exposure time should be added to the above table.

Summary of Contents for CB-140GE













































































Search results

Summary of Contents for CB-140GE

Reviews:

Related manuals for CB-140GE

Brands by name

Popular brands

JAI CB-140GE, User Manual

Search results

Summary of Contents for CB-140GE

Reviews:

Related manuals for CB-140GE

Brands by name

Popular brands