JAI CB-140GE User Manual Download

Page: 11 / 76

CM-140 GE / -RA/-UV / CB-140GE/-RA

- 9 -

3. Main Features

•

Member of C3 Compact series, covering VGA to UXGA resolution

•

1392 (h) x 1040 (v) 4.65 µm square pixels

•

1/2” progressive scan – monochrome and Bayer mosaic color versions

•

UV sensitive version CM-140GE-UV available

•

31 frames(16.14 frames for UV)/second with full resolution in continuous operation

•

30 frames(16 frames for UV)/second with external trigger and full resolution

•

Increased frame rate with vertical binning (CM-140 GE only) and partial scan

•

Exposure time from 61.168μs (117.8μs for UV)to 2 sec. using Pulse Width trigger mode

•

Programmable exposure from 61.168μs(117.8μs for UV) to 32.17 ms in Full Frame scan

•

Sequencer trigger mode for on-the–fly change of gain, exposure and ROI

•

Edge pre-select and Pulse Width control trigger modes

•

LVAL-synchronous/-asynchronous operation (auto-detect)

•

Auto iris lens video output allows a wider range of light

•

GigE Vision Interface with 10 or 8-bit output

•

Programmable GPIO with opto-isolated inputs and outputs

•

Can be connected with 100BASE-TX

•

Right Angle type is available as CM-140GE-RA and CB-140GE-RA

•

Comprehensive software tools and SDK for Windows XP/Vista

Note: CM/CB-140GE ,CM/CB-140GE-RA and CM-140GE-UV can be connected with

100BASE-TX. However, due to the limited bandwidth (100Mbps), the described

specifications such as frame rate, minimum trigger interval and so on cannot be

satisfied for 100BASE-TX connection.

Summary of Contents for CB-140GE













































































Search results

Summary of Contents for CB-140GE

Reviews:

Related manuals for CB-140GE

Brands by name

Popular brands

JAI CB-140GE, User Manual

Search results

Summary of Contents for CB-140GE

Reviews:

Related manuals for CB-140GE

Brands by name

Popular brands