JAI CB-140GE User Manual Download Page 13

Page: 13 / 76

CM-140 GE / -RA/-UV / CB-140GE/-RA

- 11 -

4.2. CM/CB-140GE-RA



Lens mount

C-mount (Note *1)



CCD sensor

1/3 inch CCD sensor



12-pin connector

DC +12V to +24V power and GPIO interface



RJ-45

Gigabit Ethernet connector with threaded holes for

thumbscrews



LED

Indication for power and trigger input



LED

GigE Network condition: LINK



LED

GigE Network condition: ACT



Holes for RJ-45 thumbscrews

When an RJ-45 connector with thumbscrews is used,

remove the two screws located above and below the

Ethernet connector (Note*2)



Mounting holes

M3 depth 3.5mm for tripod mount plate (Note*3)

*1) Note: Rear protrusion on C-mount lens must be less than 10.0mm.

*2) Note: When a RJ-45 cable with thumbscrews is connected to the camera, please do not

excessively tighten screws by using a screw driver. The RJ-45 receptacle on the camera

might get damaged. For security, the strength to tighten screws is less than 0.147

Newton meter (Nm). Tightening by hand is sufficient in order to achieve this.

*3) Note: The depth of holes is 3.5mm. When the tripod adapter plate MP-40 or MP-41 is used, use

the attached screws. If installing the camera directly, please do not use screws longer

than 3.5mm.

Fig.2 Locations (CM-140GE-RA / CB-140GE-RA)

Seri

al No

Caut

ion s

eal

GigE

POW

ER /

TRIG

FCC

seal

①　　

②

③

④

⑤

⑥

⑦

⑧

⑨

Summary of Contents for CB-140GE













































































Search results

Summary of Contents for CB-140GE

Reviews:

Related manuals for CB-140GE

Brands by name

Popular brands

JAI CB-140GE, User Manual

Search results

Summary of Contents for CB-140GE

Reviews:

Related manuals for CB-140GE

Brands by name

Popular brands