JAI BB-500 GE User Manual Download Page 68 | Manualshive

Page: 68 / 73

background image

BM-500GE / BB-500GE

66

13.2. Specification table
Specifications

BM-500GE

BB-500GE

Scanning system

Progressive scan

Frame rate full frame

15.05 frames/sec. Progressive (2072 lines/frame)

Pixel clock

60 MHz

Line frequency

31.19 kHz (1H = 32 µs)

(1924 pixel clock/line L ch and 1924 pixel clock / line R ch)

CCD sensor

2/3” Monochrome ICX625ALA

2/3” Bayer Color ICX625AQA

Sensing area

8.47 (h) x 7.10 (v) mm 2/3 inch diagonal

Cell size

3.45 (h) x 3.45 (v)



m

Active pixels

2456 (h) x2058 (v)

Pixels in video output.

Full Scan
2/3 partial Scan

                         1/2 partial Scan
                         1/4 partial Scan
                         1/8 partial Scan
                   Variable Patial Scan

Vertical Binning

Region-of-interest (ROI)

2456 (h) x 2058 (v) 15.05 fps.   H = 31.19 kHz
2456(h)  x 1372 (v)  19.97 fps     H= 31.19 kHz
2456 (h) x 1028 (v)  23.93 fps.   H =  31.19 kHz
2456(h) x  514 (v)   34.04fps.   H =  31.19 kHz
2456 (h) x 258  (v)  43.07 fps.  H =  31.19 kHz
Start line from 2 to 2050, height(lines) from 8 to 2058
2456 (h) x 1029 (v)  22.88 fps.   H = 23.77 kHz ( *Note1)

User Definable. Memory read-out

*Note1: Vertical binning is for BM-500GE only

Sensitivity on sensor (minimum)

0.34 Lux (Max. gain, Shutter OFF, 50%

video )

1.0 Lux (Max. gain, Shutter OFF,50%

Green, w/IR cut filter)

S/N ratio

More than 50 dB (0dB gain)

Digital Video output.

GigE Vision Compliant

Mono8,Mono10,Mono10_Packed

Mono 12, Mono12_Packed

GigE Vision Compliant

BAYRG8,BAYGB8,BAYRG10,BAYGB10

BAYRG12, BAYGB12

White Balance

n/a

Manual/One push

Continuous

Preset (3200K,4600K,5600K)

Iris video output. Analogue

0.7 V p-p , enabled by internal switch

Gain

Manual / AGC : -3 to +12 dB

Blemish Correction

ON / OFF

Synchronization

Internal X-tal

GPIO Module

Input/output switch

Clock Generator ( One)

Pulse Generators ( Two)

Configurable 16-in / 12-out switch

12-bit counter based on Pixel clock

19-bit counter programmable for length, start point, stop point, repeat

Hardware Trigger modes

Edge Pre-Select , Pulse Width Control, Frame Delay and Sequence

OB area transfer mode

ON / OFF

Event message

SYNC / ASYNC mode ( Trigger mode status when exposure starts )

Exposure start, Exposure end, Trigger IN, Video start, Video end

Electronic Shutter

Preset Shutter speed

Programmable exposure

Exposure Time (Abs)

Exposure Auto continuous

GPIO plus Pulse Width

OFF(1/15) and 1/30 to 1/10,000 in 10 steps

2L(64µs) to 2072 L ( 66.44ms) in 1L steps

µsec – user definable. Same range as PE

OFF to 1/250s

max. 2 sec ( Can be set by 100µs unit or Pixel Clock unit)

Control interface

Register based. GigE Vision / GenIcam compliant

Functions controlled via GigE
Vision Interface

Shutter, Gain, Black Level, Trigger mode, Read out mode,

GPIO setup ,ROI ( GenIcam mandatory functions )

GigE Vision Streaming Control

Packet size, Delayed ( Frame ) read-out, inter-packet delay

Jumbo frame can be set at max. 4K(4036) , Default packet size is 1428 Byte.

«
...
66
67
68
69
70
...
»

Summary of Contents for BB-500 GE










































































Reviews:

No comments

Related manuals for BB-500 GE

Brand: Olympus Pages: 8

Brand: Ken A Vision Pages: 2

Brand: EchoMaster Pro Pages: 4

Brand: Konica Minolta Pages: 124

Brand: GLOBIZ Pages: 6

Video-Splitter 2plus

Brand: G&D Pages: 20

DIGITAL PHOTO FRAME PF-A700B

Brand: Mustek Pages: 1

TRAIL SENTRY 119303

Brand: Bushnell Pages: 16

Brand: Dalsa Pages: 90

Thinklite TT350O

Brand: Godox Pages: 13

Brand: Equip Pages: 16

Brand: Advent Pages: 20

Brand: IC Realtime Pages: 17

Brand: Technika Pages: 8

LUMIX DMC-FX50EB

Brand: Panasonic Pages: 50

Lumix DMC-FS62EB

Brand: Panasonic Pages: 12

Lumix DMC-FX500E

Brand: Panasonic Pages: 54

Brand: Panasonic Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands