JAI BB-500 GE User Manual Download Page 55 | Manualshive

Page: 55 / 73

background image

BM-500GE / BB-500GE

53

10.2.7 Optical Black transfer Mode

It is possible for the user to decide whether the optical black (OB) portion of the image will
be transferred or not. The optical black part can be used for black reference in the
application software. Setting register 0xA41C turns the optical black transfer ON or OFF. The
default condition is OFF.

Normal Mode

OB Transfer Mode

Normal Scan

1 1228 1229 2456
1

2058

1    1617   1244 1245 2472 2488
  1

ます

2058

2/3

Partial

Scan

1 1228 1229 2456
1

1372

1  1617     1244     2472 2488
  1

ます

1372

1/2

Partial

Scan

1 1228 1229 2456
1

1029

1 1617 1244 2472 2488
1

1029

1/4

Partial

Scan

1     1228 1229   2456
  1

  514

1 1617 1244 2472 2488
1

514

1/8

Partial

Scan

1     1228 1229   2456
  1
  257

1 1617 1244 2472 2488
1

257

V Binning Scan

1 1228 1229 2456
1

1029

1 1617 1244 2472 2488
1

1029

OB ( H:32
pixels can
be added.

OB (H: 32
pixels) can
be added.

OB (H: 32
pixels) can
be added.

OB (H: 32
pixels) can
be added.

OB (H: 32
pixels) can
be added.

OB (H: 32
pixels) can
be added.

«
...
53
54
55
56
57
...
»

Summary of Contents for BB-500 GE










































































Reviews:

No comments

Related manuals for BB-500 GE

Brand: Samsung Pages: 134

Brand: Sakar Pages: 31

Brand: Yashica Pages: 33

ProScale 950 Series

Brand: Accurate Technology Pages: 53

Stylus Tough 8000 Blue - Stylus Tough 8000 12MP 2.7 LCD Digital...

Brand: Olympus Pages: 83

E300 - 14-54mm f/2.8-3.5 Zuiko ED Digital SLR...

Brand: Olympus Pages: 212

ENVIROMUX-IPCAM-NPOE

Brand: NTI Pages: 5

Brand: THOMSON Pages: 5

Brand: SecurView Pages: 4

Brand: Digital Spectrum Pages: 11

Brand: Casio Pages: 91

Brand: Intova Pages: 2

Brand: Sungale Pages: 35

Brand: Polaroid Pages: 16

Brand: Konica Minolta Pages: 19

Brand: Wizard-tk Pages: 5

Brand: Pentax Pages: 56

Brand: Hama Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands