JAI BB-500 GE User Manual Download

Page: 6 / 73

BM-500GE / BB-500GE

Table of Contents

JAI GigE

Vision Camera operation manuals ............................................................ 7

Introduction ................................................................................................. 7

Before using GigE

Vision cameras......................................................................... 7

Software installation ....................................................................................... 7

Camera operation .......................................................................................... 8

General ........................................................................................... 8

Camera nomenclature .......................................................................... 8

Main Features.................................................................................... 9

Locations and Functions ...................................................................... 10

4.1

Locations and functions ....................................................................... 10

4.2. Rear panel indicator. ............................................................................ 11

Pin Assignment ................................................................................. 11

5.1. 12-pin Multi-connector (DC-in/GPIO/Iris Video) ............................................ 11

5.2. Digital Output Connector for Gigabit Ethernet .............................................. 11

5.3. D-sub 9 pin connector for GPIO (Auxiliary) .................................................. 12

5.4. Internal DIP switch .............................................................................. 12

GPIO (Inputs and outputs) .................................................................... 13

6.1

Overview ........................................................................................ 13

6.1.1

LUT (Cross Point Switch) ........................................................................ 14

6.1.2

12-bit Counter .................................................................................... 14

6.1.3

Pulse Generators (0 to 1) ....................................................................... 14

6.2

Opto-isolated Inputs/Outputs ................................................................ 15

6.2.1

Recommended External Input circuit diagram for customer .............................. 16

6.2.2

Recommended External Output circuit diagram for customer ............................ 16

6.2.3

Optical Interface Specifications ............................................................... 17

6.3.

Inputs and outputs table ...................................................................... 17

6.4. Configuring the GPIO module .................................................................. 18

6.4.1 Input/Output Signal Selector .................................................................... 18

6.5. GPIO programming examples .................................................................. 18

6.5.1 Pulse generator setting screen .................................................................. 18

6.5.2 GPIO Plus PWC shutter ............................................................................ 20

6.5.2 Internal Trigger Generator ....................................................................... 21

7. Image output........................................................................................ 22

7.1. CCD Sensor Layout ............................................................................... 22

7.2. Vertical Binning (BM-500GE only). ............................................................ 22

7.3. Partial Scanning ( Fixed rate and variable) .................................................. 23

7.4. GigE Vision Streaming Protocol (GVSP) ....................................................... 23

7.4.1 Digital Video Output (Bit Allocation) ........................................................... 23

7.4.2 Bit Allocation (Pixel Format / Pixel Type) – BM-500GE (monochrome) ................... 24

7.4.2.1 GVSP_PIX_MONO8 (8bit) ..................................................................... 24

7.4.2.2

GVSP_PIX_MONO10 (10bit) ................................................................. 24

7.4.2.3 GVSP_PIX_MONO10_PACKED ( 10 bit ) ..................................................... 24

7.4.2.4

GVSP_PIX_MONO12 ( 12 bit ) ................................................................ 24

7.4.2.5 GVSP_PIX_MONO12_PACKED ( 12 bit ) ..................................................... 24

7.4.3 Bit Allocation (Pixel Format / Pixel Type) – BB-500GE (Bayer mosaic color) ............ 24

7.4.3.1 GVSP_PIX_BAYRG8 “ BayreRG8 “ ........................................................... 25

7.4.3.2 GVSP_PIX_BAYRG10 “Bayer RG10”......................................................... 25

7.4.3.3 GVSP_PIX_BAYRG12 “ Bayer RG12” ........................................................ 25

7.4.3.4 GVSP_PIX_BAYGB8 “Bayer GB8” ........................................................... 25

7.4.3.5 GVSP_PIX_BAYGB10 “ Bayer GB10” ........................................................ 25

7.4.3.6 GVSP_PIX_BAYGB12 “ Bayer GB12” ........................................................ 25

Summary of Contents for BB-500 GE










































































Search results

Summary of Contents for BB-500 GE

Reviews:

Related manuals for BB-500 GE

Brands by name

Popular brands

JAI BB-500 GE, User Manual

Search results

Summary of Contents for BB-500 GE

Reviews:

Related manuals for BB-500 GE

Brands by name

Popular brands