JAI BB-500 GE User Manual Download | Manualshive

Page: 3 / 73

background image

BM-500GE / BB-500GE

3

Notice

T

he material contained in this manual consists of information that is proprietary to JAI Ltd.,

Japan  and  may  only  be  used  by  the  purchasers  of  the  product.  JAI  Ltd.,  Japan  makes  no
warranty  for  the  use  of  its  product  and  assumes  no  responsibility  for  any  errors  which  may
appear or for damages resulting from the use of the information contained herein. JAI Ltd.,
Japan reserves the right to make changes without notice.

Company  and  product  names  mentioned  in  this  manual  are  trademarks  or  registered
trademarks of their respective owners.

Warranty

For information about the warranty , please contact your factory representative.

Certifications

CE compliance

As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC
(Electromagnetic  compatibility),  JAI  Ltd.,  Japan  declares  that  BM-500GE  and  BB-500GE
comply with the following provisions applying to its standards.
EN 61000-6-3  (Generic emission standard part 1 )
EN 61000-6-2  (Generic immunity standard part 1)

FCC

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital
device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable
protection  against  harmful  interference  in  a  residential  installation.    This  equipment
generates,  uses  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in
accordance with the instructions, may cause harmful interference to  radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-

Reorient or relocate the receiving antenna.

-

Increase the separation between the equipment and receiver.

-

Connect the equipment into a outlet on a circuit different from that to which the receiver
is connected.

-

Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications to this unit not expressly approved by the party
responsible for FCC compliance could void the user’s authority to operate the
equipment.

«
1
2
3
4
5
...
»

Summary of Contents for BB-500 GE










































































Reviews:

No comments

Related manuals for BB-500 GE

Brand: VEKOOTO Pages: 10

Brand: Xblitz Pages: 64

Brand: Vantrue Pages: 28

Brand: SBIG Pages: 47

Brand: Ecco Pages: 24

Brand: EastLink Pages: 4

Brand: Casio Pages: 18

Brand: LENCO Pages: 3

Brand: Roadmaster Pages: 2

Brand: Voyager Pages: 16

Brand: Pentax Pages: 48

Brand: Axxera Pages: 2

Brand: CompuSTAR Pages: 72

Hello Kitty KT7004

Brand: Spectra Pages: 11

Brand: Casio Pages: 41

Brand: Doerr Pages: 6

Brand: Crest Audio Pages: 2

Brand: Survision Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands