JAI BB-500 GE User Manual Download Page 33 | Manualshive

Page: 33 / 73

background image

BM-500GE / BB-500GE

31

8. Network configuration



For details of the network settings, please refer to the “Getting Started

Guide” supplied with the JAI SDK.

8.1.

GigE Vision Standard Interface

The  BM-500GE  and  BB-500GE  are  designed  in  accordance  with  the  GigE  Vision  standard.  In
transmits  digital  images  over  Cat5e  or  Cat6  Ethernet  cables.  All  camera  functions  are  also
controlled via the GigE Vision interface.

The  camera  can  operate  in  continuous  mode,  providing  an  endless  stream  of  images.  For
capturing individual images, related to a specific event, the camera can also be trigged. For
precise triggering, it is recommended to use a hardware trigger applied to the Hirose 12-pin
connector. It is also possible to initiate a software trigger through the GigE Vision interface.
However, when using software trigger, certain latency inherent to the GigE interface must be
anticipated.  This  latency,  that  manifests  itself  as  jitter,  greatly  depends  on  the  general
conditions and traffic on the GigE connection. The frame rate described in this manual is for
the ideal case and may deteriorate depending on conditions.

When using multiple cameras (going through a switch and/or a single path) or when operating
in a system with limited transmission bandwidth the Delayed Readout Mode and Inter-Packet
Delay functions can be useful.

8.2. Equipment to configure the network system

8.2.1 PC

The PC used should have the following performance or better
1) Recommended CPU

: Core2 Duo 2.4GHz or better,

Better than Core2 Extreme

2) Recommended memory

: 2Gbyte or more

3) Video card

: Better than PCI Express Bus Ver.1.0 x16

VRAM should be better than 256MByte, DDR2

4) Other

: The resident software should not be used

8.2.2 Cables

GigEVision configures the system by using 1000BASE-T.  (100BASE-T can be used with
some restriction. Refer to chapter 8.3.6). In the market, CAT5e (125MHz), CAT6
(250MHz) and CAT7 (600MHz) cables are available for 1000BASE-T. There are
crossover cables and straight through cables available. Currently, as most equipment
complies with Auto MDI/MDI-X, please use straight through cables. (Among crossover
cables, a half crossover type exists, which the Ethernet will recognize as 100BASE-T).

8.2.3 Network card (NIC)

The network card should comply with 1000BASE-T and also have the capability of
JUMBO FRAMES. When the jumbo frame size is set at a larger number, the load on the
CPU will be decreased. Additionally, as the overhead of the packet is decreased, the

transmission will have more redundancy.

JAI confirms the following network cards.

«
...
31
32
33
34
35
...
»

Summary of Contents for BB-500 GE










































































Reviews:

No comments

Related manuals for BB-500 GE

Brand: NcTech Pages: 9

Brand: Gator Pages: 32

Brand: Polaroid Pages: 11

Brand: Aigo Pages: 2

Brand: GUARDO Pages: 42

Brand: Konica Minolta Pages: 124

ATLONA Captivate AT-CAP-FC110

Brand: Panduit Pages: 24

Brand: Axis Pages: 98

Brand: Qware Pages: 23

Brand: Zee Pages: 13

Brand: Recordex Pages: 2

Brand: COXPAL Pages: 27

Brand: Casio Pages: 39

Brand: JENDIGITAL Pages: 30

Brand: Cansonic Pages: 60

Brand: Panasonic Pages: 58

Lumix DMC-TZ70GN

Brand: Panasonic Pages: 305

Brand: Genee Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands