background image

RESPONSIBILITIES OF OTHERS

Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user.  They are responsible for ensuring the unit
is free of defect or damage.  Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In the event of a problem, the unit
must not be installed.  The Company is not responsible for failures or damage that could have been discovered, repaired, or avoided by proper inspection and testing prior
to installation.

Damage occurring in transit is the responsibility of the carrier.  The user or installer MUST open the crate and inspect the unit for damage when it is delivered. If damage
is discovered, it must be reported immediately to the seller and the carrier in writing, and an inspection requested.  Failure of the carrier to respond should be reported to
the seller and the carrier. Your freight claims should be filed promptly thereafter.

It is the responsibility of the installer, building contractor, or user to provide access for service.  The Company is not responsible for any costs relating to obtaining access
for repair. The user shall bear such costs and, if appropriate, must seek recovery from the installer.

Damage occurring to the unit during installation is the responsibility of the installer and/or building contractor and damage occurring thereafter is the responsibility of the
user.

Failure of any optional equipment is the sole responsibility of the equipment manufacturer. (Options and accessories manufactured by the Company are warranted for ninety
(90) days from the original date of purchase for parts only.)

The Distributor or Dealer is responsible for knowing local code requirements and notifying the installing contractor and/or user of these requirements at the time of purchase.
The Company is not responsible for costs to modify any product to obtain any code approval, such as city, county, or state building codes.

WARRANTY SERVICE

For the customer's benefit, the Company maintains a list of independent service personnel to perform required warranty service repairs.  Such firms are not agents or
representatives of the Company and cannot bind the Company by words or conduct.

The Company will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the
warranty; the user has informed an Authorized Jacuzzi Whirlpool Bath Dealer or Warranty Service Department  Representative of the nature of the problem during the
warranty period; conclusive evidence (e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure occurred or was
discovered within the warranty period; an authorized independent service person or Company representative has been permitted to inspect the unit during regular
business hours within a reasonable time after the problem was reported by the user.

In order to obtain warranty service, consult your Jacuzzi Whirlpool Bath Dealer.

If you are unable to contact a Jacuzzi Whirlpool Bath Dealer, call or write:

Jacuzzi Whirlpool Bath

Warranty Service Department

P.O. Drawer J

Walnut Creek, California 94596

Call: (925) 938-7411

 To obtain warranty replacement for factory-installed components for Company supplied options and accessories manufactured and supplied by the Company, call or write
the above. Provide a description of the problem and proof of purchase.  You will be instructed how to obtain replacements and where to return, at your expense, the failed
component(s), option(s), or accessory(ies).

All replacement parts, equipment, and repairs shall assume the remaining warranty period of the part(s) replaced.

The Company's warranty obligation shall be discharged upon tender of replacement or repair.  The customer's refusal to accept the tender terminates the Company's warranty
obligation.

Jacuzzi

®

 is a Federally registered trademark owned by Jacuzzi Inc.  ©Copyright 2000 Jacuzzi Whirlpool Bath R907000 4/00

Ninety-Day

Parts Only

Limited Warranty

On

Accessory(ies)

Warranty

Registration Card

Ninety-Day

Parts Only

Limited Warranty

On

Accessory(ies)

WHIRLPOOL

 

BA

TH

R

R907000

1.

How did you first hear about this Jacuzzi

®

 product?

(    ) Advertisement      (    ) Article in Magazine/Newspaper

(    ) Visited Dealer/Plumbing Supplier      (    ) Yellow Pages

(    ) Builder/Plumber/Remodeler      (    ) Decorator/Architect

(    ) Visited Retailer/Home Center Store

(    ) Word of Mouth . . . Friend/Relative/Acquaintance

(    ) Other . . . Please Describe

__________________________________

2.

Who first gave you specific information about this product (specifications,

prices, etc.)?

(    ) Dealer/Plumbing Supplier      (    ) Builder      (    ) Remodeler

(    ) Plumbing Contractor      (    ) Retailer/Home Center Store

(    ) Decorator/Architect      (    ) Already Installed

3.

What was the main reason for purchase?

(    ) Styling      (    ) Warranty Service      (    ) Product Features

(    ) Brand Name      (    ) Price      (    ) Hydrotherapy

(    ) Home Resale

_____________________________________________

(    ) Other

___________________________________________________

4.

Who finally decided which product you would buy?

(    ) Self      (    ) Spouse      (    ) Self and Spouse Together

(    ) Other Family Member      (    ) Designer/Architect

(    ) Builder/Plumber/Remodeler      (    ) Already Installed

5.

Who installed?      (    ) Already installed/New Home

(    ) Contractor/Plumber when remodeling

(    ) Self/Spouse when remodeling

(    ) Other

___________________________________________________

6.

What is the current market value of this property?

Please estimate $

_____________________________________________

7.

What is the age of the head of the household?

_________________

years

8.

What other manufacturers did you consider?

(    ) Cal Spas      (    ) Sundance     (    ) Catalina      (    ) Master

(    ) Hot Springs      (    ) Dimension One      (    ) Marque

(    ) Other (Specify)

___________________________________________

9.

How long did you shop before purchasing unit?

(    ) 1 day

(    ) 2 months-6 months

(    ) 2-7 days

(    ) 6 months-1year

(    ) 1 week-2 weeks

(    ) 1 year-2 years

(    ) 2 weeks-4 weeks

(    ) +2 years

(    ) 1 month-2months

10.

Approximately how long have you lived in this home?

_________________

Please indicate, approximately, the total annual income of your household.

(    ) Up to $24,999                  (    ) $50,000 to $74,999

(    ) $25,000 to $29,999           (    ) $75,000 to $99,999

(    ) $30,000 to $39,999          (    ) $100,000 to $149,999

(    ) $40,000 to $49,999          (    ) $150,000 and Above

11.

Was your purchase process?

(    ) Very easy     (    ) Easy      (    ) Difficult      (    ) Very difficult

12.

How technically aware were you of the patented Jacuzzi

®

 jet system prior to

your purchase?

(    ) Not aware      (    ) Somewhat aware      (    ) Very aware

This card must be filled out and returned to the address printed on the

other side within thirty (30) days from date of purchase in order for this

warranty to be come effective.

 Purchaser's Name

_____________________________________

Purchaser's Address

____________________________________

                                 City

__________

State

_____

Zip

_______

Date of Purchase

______________________________________

Model Name

__________________________________________

Serial Number

________________________________________

Dealer's Name

________________________________________

Dealer's Address

_______________________________________

Summary of Contents for Aero Select





























Reviews: