Jacobsen ECLIPSE 360, Safety, Operation & Maintenance Manual

Page: 28 / 148

B
en-28
Safety, Operation, & Maintenance Manual
CONTROLS
Lithium
OPERATOR MODE ___________________________________________________
Operator mode is used by the opera -
tor to view attachment mode, system
voltage information, travel speed,
reel motor current, reel motor speed,
switch status, operation hours, and
stored alarms. Press the orange but -
tons (AM and AN) on the LDU to
toggle between the different dis -
plays.
Mower Attachment Mode: Displays
current mower attachment mode.
Reel Motor On/Off: Allows reel motor
operation to be disabled for training
purposes or practice cutting. Mow
and lift system will function normally,
with the exception of the reel motors
operating. Press black button (AL) to
toggle between reel on and off. LDU
screen will be locked on REEL
MOTORS OFF screen until reel
motors are turned back on. Reel
motors will also be enabled by
cycling the system power switch.
NOTE:
Enabling reel motors on this
screen will not enable reel motors in
Mode 3 Roller or Mode 5 Spiker.
System Volts: Displays the system
voltage. Normal operating voltage is
between 43 and 60.5 volts, depend -
ing on the power module installed. High or low voltage faults may occur of system voltage goes above 60.5 volts for 5
seconds or drops below 43 volts for ten seconds. Some machine functions may be disabled in cases of high or low sys -
tem voltage.
Travel Speed: Displays speed mower is traveling. Travel speed may be limited due to Maximum Mow Speed and Travel
Speed values set in Maintenance Mode, or to meet current FOC setting.
Reel Motor Current: The reel motor current screen is provided for the operator and mechanic to help identify problems
before damage to the reel motor occurs. Notify maintenance personnel if one reel motor is drawing a higher current load
than the other two motors. The screen displays the reel motor current for all three reels. The number in the upper left cor -
ner of the screen is for the left reel motor, the number in the upper right corner of the screen is for the right reel motor, and
the number on the second row of the screen is for the center reel motor. A fault will occur if reel motor current is over 35
amps for 30 seconds.
Reel Motor Screen: The reel motor speed screen displays the reel motor speed for all three reels. The number in the
upper left corner of the screen is for the left reel motor, the number in the upper right corner of the screen is for the right
reel motor, and the number on the second row of the screen is for the center reel motor. All three reel motors should be
operating within 50 rpm of each other.
Enter Pin? Screen: Used to enter Maintenance Mode. Enter the four digit pin number to access Maintenance Mode.
Alarms Screens: Used to view alarms stored in system memory. Alarm message will appear on the screen as they
occur for a few seconds, and a beep may sound, depending on the fault encountered. The alarm is then stored in system
memory until key switch is turned to off position.
JACOBSEN
REEL MOTOR
ON
MODE 1
REEL
SYSTEM VOLTS
54 VDC
BATTERY SOC
39%
HOURS
000103.9
Mower
Attachment
Modes
Operator
mode
Displays reel
reel motor status
Displays SOC
Displays system
voltage
Alarm Screens
Maintenance
Mode Entry
Screen
ENTER PIN?
NO ALARMS
DETECTED
Displays engine
operation hours
0000 0000
0000 RPM
Displays speed
for reel motors
TRAVEL SPEED
0.0 MPH
Displays
travel speed
00 REEL 00
00 AMPS
Displays current
for reel motors
REEL MOTOR
OFF
Displays reel
reel motor status
PIN
0
ŻŻŻ
REVIEW
ALARMS?
Pin
JACOBSEN
REEL MOTOR
ON
MODE 1
REEL
SYSTEM VOLTS
54 VDC
BATTERY SOC
39%
HOURS
000103.9
Mower
Attachment
Modes
Operator
mode
Displays reel
reel motor status
Displays SOC
Displays system
voltage
Alarm Screens
Maintenance
Mode Entry
Screen
ENTER PIN?
NO ALARMS
DETECTED
Displays engine
operation hours
0000 0000
0000 RPM
Displays speed
for reel motors
TRAVEL SPEED
0.0 MPH
Displays
travel speed
00 REEL 00
00 AMPS
Displays current
for reel motors
REEL MOTOR
OFF
Displays reel
reel motor status
PIN
0 ŻŻŻ
REVIEW
ALARMS?
Pin