manualshive.com logo in svg

Jackson RackStar 44, Installation, Operation And Service Manual, Page: 7 / 80

Share
Download
Jackson RackStar 44 Installation, Operation And Service Manual Download Page 7

PARTS

 

Rinse Assembly ........................................................................................................................

45

Pawl Bar Assembly

 ...................................................................................................................

47

Rack Paddle Assembly

 .............................................................................................................

48

Drive Assembly .........................................................................................................................

49

Ventilation Cowl

 ........................................................................................................................ 51

Ventilation Cowl for Unhooded Side-Loader

 ............................................................................. 52

Motor Overloads ....................................................................................................................... 53

Side-Loaders ............................................................................................................................

54

Side-Loader Drive Linkage ....................................................................................................... 57

Steam Heating Coil Assembly ............................................................................................ 58

Booster Heater Option (Electric) ............................................................................................... 59

Frame Assembly ....................................................................................................................... 60

Door Assemblies ....................................................................................................................... 61

Miscellaneous Parts

 ............................................................................................................. 62

SCHEMATICS

Booster Heater, 3-Phase

 .......................................................................................................... 63

Booster Heater, 1-Phase, 12 kW

 ..............................................................................................

64

Booster Heater, 1-Phase, 18 kW

 .............................................................................................. 65

Steam Booster Heater .............................................................................................................. 66

RackStar 208/230 V, 50/60 Hz, 1-Phase

 .................................................................................. 67

RackStar 208/230 V, 50/60 Hz, 3-Phase

 .................................................................................. 68

RackStar 380/480 V, 50/60 Hz, 3-Phase

 .................................................................................. 69

RackStar Side-Loader .............................................................................................................. 70

ADDENDUM

Display Template ...................................................................................................................... 71

TABLE OF CONTENTS

Summary of Contents for RackStar 44

















































































Reviews:

No comments