Jackson RackStar 44 Installation, Operation And Service Manual Download Page 44

Page: 44 / 80

07610-004-33-05-B

PARTS

VOLTAGE

PHASE

PART NUMBER

CONTACTOR

208

04540-121-68-45

05945-111-68-37

230

04540-121-68-46

05945-111-68-37

208

04540-121-68-45

05945-002-24-70

230

04540-121-68-46

05945-002-24-70

460

04540-121-68-47

05945-002-24-70

208

04540-121-79-30

05945-111-68-37

230

04540-121-79-31

05945-111-68-37

208

04540-121-79-30

05945-002-24-70

230

04540-121-79-31

05945-002-24-70

460

04540-121-79-32

05945-002-24-70

SERVICE NOTES:

When replacing wash heaters, it is highly recommended to change the gasket as well. Once installed,

gaskets become compressed and are subject to extreme temperature changes. Replacing the gasket with the heater

might prevent future leaks.

The nuts used to secure the heater to the casting should be torqued to 16 in-lbs. After tightening, the unit should be allowed

to heat up and operate normally for approximately 30 minutes. Secure power to the machine and check the nuts once more

to verify they are torqued to 16 in-lbs.

WASH HEATERS

Summary of Contents for RackStar 44

















































































Search results

Summary of Contents for RackStar 44

Reviews:

Related manuals for RackStar 44

Brands by name

Popular brands

Jackson RackStar 44, Installation, Operation And Service Manual

Search results

Summary of Contents for RackStar 44

Reviews:

Related manuals for RackStar 44

Brands by name

Popular brands