Jackson DishStar HT Installation, Operation And Service Manual Download

Page: 28 / 68

07610-004-37-13-E

PROBLEM

POSSIBLE CAUSE

REMEDY

Wash

temperature

not at required

temperature

range.

1. Water level low.

2. RTD setpoint too slow.

3. Defective RTD.

4. Wash heater defective.

5. Defective heater contactor R1.

1. Check water level. If low, run new fill cycle.

2. Check fault screen. Adjust wash temperature setpoint

3. Replace.

4. Replace heater element.

5. Replace.

Rinse water

not at

required

temperature

range.

1. Incoming rinse water does not

meet minimum criteria indicated on

machine data plate.

2. RTD is defective.

3. Rinse heaters damaged.

4. Setpoint screens set low.

1. Adjust as required.

2. Replace if necessary.

3. Check amperages. Replace if necessary.

4. Adjust rinse tank setpoint.

Machine

doesn’t drain

when power

button is

pressed.

1. Drain clogged.

2. Defective drain valve.

1. Remove obstruction.

2. Replace.

No indication of

pressure.

1. Water turned off.

2. Pressure gauge failure.

1. Turn water on.

2. Replace pressure gauge.

COMMON PROBLEMS

TROUBLESHOOTING

Summary of Contents for DishStar HT





































































Search results

Summary of Contents for DishStar HT

Reviews:

Related manuals for DishStar HT

Brands by name

Popular brands

Jackson DishStar HT, Installation, Operation And Service Manual

Search results

Summary of Contents for DishStar HT

Reviews:

Related manuals for DishStar HT

Brands by name

Popular brands