Jackson DishStar HT Installation, Operation And Service Manual Download

Page: 26 / 68

07610-004-37-13-E

PREVENTATIVE MAINTENANCE

MAINTENANCE

PREVENTATIVE

MAINTENANCE

The manufacturer highly recommends that any maintenance and repairs not specifically

discussed in this manual be performed only by QUALIFIED SERVICE PERSONNEL.

Performing maintenance on your dishmachine may void your warranty, lead to larger

problems, or even cause harm to the operator. So if you have a question or concern, do

not hesitate to contact a QUALIFIED SERVICE AGENCY.

By following the operating and cleaning instructions in this manual, you should get the

most efficient results from your machine. As a reminder, here are some steps to take to

ensure that you are using the dishmachine the way it was designed to work:

1. Ensure that the water temperatures match those listed on the machine data plate.

There can be a variety of reasons why your water temperature could be too low.

2. Ensure that all strainers are clean and securely in place before operating the machine.

When cleaning out strainers, do NOT beat them on waste cans. Wipe out strainers
with a rag and rinse under a faucet if necessary. Use a toothpick to dislodge any
stubborn debris.

3. Ensure that all wash and rinse arms are secure in the machine before operating.

4. Remove as much soil from dishes by hand as possible before loading into racks.

Do not overfill racks.

6. Ensure that glasses are placed upside-down in the rack.

Ensure that all chemicals being injected into machine have been verified at

the correct

concentrations.

8. Clean out the machine at the end of every workday per the Shutdown and Cleaning

section of this manual.

9. Follow all safety procedures, whether listed in this manual or put forth by local, state,

or national codes/regulations.

Summary of Contents for DishStar HT





































































Search results

Summary of Contents for DishStar HT

Reviews:

Related manuals for DishStar HT

Brands by name

Popular brands

Jackson DishStar HT, Installation, Operation And Service Manual

Search results

Summary of Contents for DishStar HT

Reviews:

Related manuals for DishStar HT

Brands by name

Popular brands